Question about 2005 Buick LeSabre

1 Answer

Need instructions for replacing 94 Buick LeSabre window module.

Need instructions on how to replace a 94 Buick LeSabre power window control module on drivers side door.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

2002 BUICK LESABRE REAR DRIVER SIDE DOOR POWER WINDOW UP CABLE IS OFF TRACK WINDOW WILL NOT STAY UP HOW CAN I REPAIR THAT

Posted on Aug 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the srs control module located


Marie, I think it maybe under right front seat. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Remove SRS Airbag Computer Control Module Reset Location MyAirbags...

2002 Buick LeSabre srs control module location Google Search

http://www.diycardoctor.com/Downloads/SRS%20Airbag%20Repair%20Guide/GM%20SRS%20Airbag%20Location.txt

found this helpful answer from buick mechanic on JustAnswer com

Mar 21, 2016 | 2002 Buick LeSabre

1 Answer

I have a 94' buick century special 4 cyl. I need


Generally speaking, the module is mounted on the side of the block and the coils are mounted to the module. You can remove the entire assembly and then swap the coils over to the new module.
There should be a wiring harness plugged into the end of the module.

May 04, 2013 | Cars & Trucks

1 Answer

94 Buick lesabre, new blower motor and new control module. Blower stays on even with key out of ignition. What could be the issue? Relay or control module?


The only way for the blower to still get power with the key off...means the resistor to the blower motor is bad...The resistor is located on the firewall...under the plastic shroud...this should fix your problem...nice Buick...:)

Jan 18, 2011 | 1994 Buick LeSabre

1 Answer

94 buick lesabre 3800 engine, stalls after 10 mile drive and will not start till cools. replaced TPS, Fuel pumpand filter, cam sensor, crank sensor, and ignition control module.


next time it won't run after it heats up, spray or pour water in crank sensor and see if it will start. I have seen new crank sensors go bad.

Jan 08, 2011 | 1994 Buick LeSabre

2 Answers

I need to replace ny 1995 buick lesabre ignition control module ...


the ignition control module is mounted to the left cylinder head. more precicely, under the 3 coils

Jan 03, 2011 | 1995 Buick LeSabre

2 Answers

I have a 94 buick la sabre stalls when warm has spark no fuel pressure also loses power to power windows and locks,when car sits it will start and windows and locks will also work.runs a little while and...


Sounds like you a loose 12V connection at the relay box.Locate the relay box and when the engine is running wriggle the wiring harness or shake the relay bow and see if that's when the engine stalls. You may even have a bad / loose ground to the relays.

Apr 08, 2010 | 1994 Buick LeSabre

2 Answers

94 buick lesabre engine shut down while driving on the highway today.had this yesterday and my mechanic placed on diagnostic scanner.scanner reads rr module problem.i do have code as for its not listed on...


PROBLEM:car does not always start or car shuts down while driving.SOLUTION:replace module!the 1994 LeSabre has two options the ECO-1 or the OBDM-1.My LeSabre was repaired by a master mechanic,who also replaced the computer because it was fried.My mechanic used the OBDM-1 module and replaced the computer haven't had a problem since.

Sep 11, 2009 | 1994 Buick LeSabre

1 Answer

94 LeSabre inner door panel removal


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Apr 22, 2009 | 1994 Buick LeSabre

Not finding what you are looking for?
2005 Buick LeSabre Logo

733 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...