Question about 2000 Dodge Dakota Quad Cab

1 Answer

Cps i have a 2002 dodge ram 4.7L. i got code p0320 and replaced the crankshaft position sensor, the problem persists. the vehicle stalls out one at running temp., the tach jumps all over the place as its dying. Any adivce?

Posted by on

  • bojac Mar 24, 2009

    same problem with code 0320 someone said to replace the cam position sensorr in which i cannot seem to locate on my dodge ram 2002 4.7



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

Did you reset the computer after you replaced the crankshaft position sensor?

If you have,it may just be the connectors on the ECM.

If not,try this first.

To reset your engine codes:
Remove the negative terminal of your battery.
Turn your ignition key to START and hold it there for about 15 seconds.
Turn your ignition key to OFF and remove it.
Reconnect the negative terminal of your battery.
Test the vehicle.

Posted on Jan 09, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Went to Deq for emissions test and the diagnostic codes read p0320 on 2004 Hyundai sonata what needs to be replaced?

P0320 =no signal detected from crankshaft position sensor during cranking, my guess is replace the CPS

Feb 24, 2015 | 2004 Hyundai Sonata

1 Answer

What are these codes p1779, 11780,po440,po341, replaced cam position censor

Try replacing the crankshaft position sensor. I had a 1998 dodge ram that had that same issue. Thats what it was.
Its by the flywheel under the vehicle. probably on the passenger side.

Apr 05, 2014 | 2002 Saturn VUE

1 Answer

I have a 2000 dodge Durango with the 4.7L engine in it. on my way home it started to shutter and lose power. had a friend put his code reader on it and it came up with error codes...

P0320 is crankshaft sensor and the last code is an ignition coil malfunction probably caused by the position sensor error.
Could be a faulty connector. Could be the crankshaft sensor.

Sep 20, 2017 | Cars & Trucks

2 Answers

What is the cps

Hi there:
A CPS (Crankshaft Position Sensor) is an electronic device used in an internal combustion engine to monitor the position or rotational speed of the crankshaft.

Hope this helps.

Dec 24, 2012 | 1997 Dodge Caravan

1 Answer


Hello! The code is indicating a defective Crankshaft Positioning Sensor (CPS) or the wiring to it ...But before you replace that sensor be advised that a Technical Service Bulletin has been written for this fault...TSB-#04-14-09...The harness from the Alternator rubs against the engine. ..Besides chaffing the pins inside the alternator connecter (male & female) are susecptible to corrosion...Check your VIN# and let me know if your vehicle was built before or after 4/2/04...After 4/2/04 a protective sleeve was installed over the harness...Also check the harness from the alternator to see if the sleeve has been installed..............Send a comment and I'll take it from there if the CPS is in-fact defective......Guru...saailer

Dec 26, 2011 | 2004 Ford Expedition

1 Answer

2005 Kia Sedona, Trouble Code P0320. Everything I read online tells me its a Crankshaft Sensor. I called Kia and then sent me to were it says that the code is an Ignition System Failure...

This is a common problem usually related to the crankshaft position sensor. Before you replace it, disconnect the electrical connector to the CPS sensor and clean it with electrical contact spray and add a dab of dielectrical grease. If the problem continues, replace the CPS sensor. It is easy to replace and is not very expensive. It just bolts to the engine block with one or two bolts. I believe the CPS sensor on the Sedona is behind the timing cover on the front of the engine.

Feb 08, 2010 | 2005 Kia Sedona

2 Answers

I have a 2000 dodge durango, I have a code P0320.

above me is right it's a faulty crankshaft position sensor. Hard to get this out so it may be cheap enough to have them change it at the shop. Only a $32 part

Apr 14, 2009 | 2000 Dodge Dakota Quad Cab

1 Answer

Engine stalls in drive after check engine light came on.

Have it sacnned for a code. it seems to be the speed sensor at the tranny.or the crankshaft position sensor. hope this helps. will you please vote ?

Dec 19, 2008 | 2007 Dodge Ram 1500 Quad Cab Sport

Not finding what you are looking for?
2000 Dodge Dakota Quad Cab Logo

559 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides