Question about 2004 GMC Envoy

Open Question

Brake light switch 2003 envoy

How does the switch get removed
how do you remove the clip or whatever is holding the switch on

Posted by on

5 Suggested Answers

  • 840 Answers

SOURCE: 2003 gmc envoy xl brake lights dont work

sounds like a fuse look under the dash panel for fuse cover look at the back of cover and check that fuseThanks for using fix ya Please rate my response thank you very much

Posted on Jan 31, 2009

  • 3 Answers

SOURCE: 2003 gmc envoy xl brake lights dont work

theres usually a pressure switch behind the brake pedal, sometimes the plastic hex nut rattles loose and you have to retighten it.

Posted on Apr 12, 2009

goofduck
  • 490 Answers

SOURCE: remove tail light assembly

there are plastic clips on it just take your time and they will come out

Posted on Apr 21, 2009

  • 1 Answer

SOURCE: Brake Light Switch clip on 94 GMC Pickup

My 1996 Brake light clip needed to spread open with a screw driver(some what like a round spring) and with another screw driver push the switch up the pin. The switch will push the clip off the Pin. The pin has a head that needs to clear clip while the spring clip is spread open. It took me a while to figure out.

Posted on Jun 08, 2009

  • 20 Answers

SOURCE: Removal of Brake light switch on a 1996 cheverolet 1500 pickup

1. Disconnect negative battery cable
2. Use a snap ring pliers to remove retainer from brake pedal pin.
3. Remove the switch by unsnapping it from the pushrod, and disconnect wiring harness from switch.

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the tail light fuse?


Rear Lights May Be Out Due To Failed Light Socket Plate ...

repairpal.com > Problems > GMC > Envoy
no tail light on passenger side. replaced tail light circuit board, fuses and bulbs. I havebrake lights ... 2003 GMC Envoy75,000Visitor. My brake light got ... How do I replace the high mount third brake light on a 2002 gmc envoy? The light does ...

Chevy Trailblazer- No Brake Lights! It's an easy fix.. - YouTube

? 12:22
https://www.youtube.com/watch?v=m0GkI5Jmrgo
Sep 7, 2014 - Uploaded by CheapGeek
My 2008 Chevy Trailblazer had no brake lights! It was ... Chevy Silverado 88-98 brake light switch replacement GMC Sierra tahoe Suburban ...

GMC Envoy XL: brake lights..the fuses and the bulbs..lights ...

www.justanswer.com > GM
images for 2003 gmc envoy wiring

Jan 17, 2016 | 2003 GMC Envoy

1 Answer

Free 2006 gmc envoy brake light switch replacement procedure


Remove the panel under the dash. Look at the brake pedal and follow it up to the brake light switch. Two wires going to it. there is a plastic clip that holds it in place, Pull it off. The clip comes with the new switch. Replace it. To easy. Have a flash light to see..

Oct 26, 2014 | 2006 GMC Envoy

1 Answer

2003 GMC Envoy brake lights don't work. I changed all of the bulbs and checked all fuses related to the brakes. But, all 3 brake lights stilll don't work. Please advise what this could be or what to try...


45f0f078-f718-4dfc-ba09-177f0829dd1e.jpgI would say it's the stop lamp switch located at the brake pedal shaft (see picture). You should have power at all times to the orange wire on the connector at that switch. If you do more than likely that's your problem. If you're mechanically inclinded it's fairly simple to replace. removing it can be a pain due to its location. Hope this helps.....

Sep 04, 2013 | 2003 GMC Envoy

1 Answer

2003 gmc envoy rear lights won't turn off


As for the brake lights i would think that the brake light switch is faulty.As for the parking lights i think that the parking light relay is sticking.Switch the relay with another one in the fuse panel with the same part number to see if thats the problem or not.

Jun 05, 2012 | 2003 GMC Envoy

1 Answer

Were the module for the brake lights on 2003 envoy


I'm not sure if there is a brake "module". If you're having a problem with your brake lights...
You checked the fuses?
Are you sure the bulbs are OK?
The brake light switch is probably what you're looking for. It should be attached to the brake pedal arm at the master cylinder linkage. You probably have to remove a plastic panel under the dash. The switch may look like this:

zeevert_49.jpg

Mar 27, 2011 | 2004 GMC Envoy

2 Answers

Excursion limited edition. Brake lights stay on.


Check that the pedal height isn't sagging due to low brake fluid level. Also check for adjustment of the brake light switch or the BPP (Brake Pedal Position) switch.

Brake Pedal Position (BPP) Switch Removal & Installation To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect brake pedal position (BPP) switch electrical connector.
  3. Remove self locking pin.
  4. Remove switch from brake master cylinder push rod.
  5. Remove push rod spacer.
  6. Remove push rod bushing.
To Install:
  1. Install push rod bushing.
  2. Install push rod spacer.
  3. Install switch to brake master cylinder push rod.
  4. Install self locking pin.
  5. Connect electrical connector.
  6. Connect battery negative cable.
prev.gif next.gif

Jan 25, 2011 | 2003 Ford Excursion

1 Answer

No brake lights 1985 f-150


The problem more than likely exists with the brake light switch. It is located under the steering column on the brake pedal shaft. There should be a kotter pin or clip that holds it in place. Remove pin or clip and carefully slide the brake rod off the brake pedal shaft. Disconnect wiring and remove completely. To install, just simply reverse the order of removal. On some model Fords, the brake light switch slides over a rod on the brake pedal shaft. If this is the case, you will need to pull forward on the brake pedal shaft (slightly) to remove the switch. Keep me informed if possible. Any other help, feel free to contact me.

Dec 11, 2010 | 1985 Ford F150

1 Answer

GMC 2003 Envoy SLT my back break lights and tailbar lights stay on when I turn the car off. What could the problem be?


This most likely is a bad or incorrectly adjusted brake light switch. The brake light switch is located under the dash next to the brake pedal arm.

Oct 05, 2010 | 2003 GMC Envoy

1 Answer

Brake light switch removal on a 2005 chevy trailblazer


Hi:
Your Brake light switch is mounted up near the top of the brake pedal arm. it is held inplace with a metal pin & a clip, as well as a small electrical connector. Basically, you need to unplug the connector, remove the clip, and pull out the pin that holds the assembly in place.

Sep 22, 2010 | 2005 Chevrolet TrailBlazer

1 Answer

How to blead brakes on 2003 gmc envoy?


There should be a bleader valve located at each wheels brake assembly. Should be somewhere on the back side of the caliper. Have a second person inside the cab. With the vehicle turned off and the brake fluid cap removed, have the second person pump and hold the brakes. While holding release the bleader valve. Close the bleeder valve. Repeat above process until all air is out of the line. Repeat on the remaining three wheels. Make sure while doing this though you keep the brake fluid full.

Sep 02, 2009 | 2003 GMC Envoy

Not finding what you are looking for?
2004 GMC Envoy Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...