Question about 1995 Dodge Dakota

1 Answer

Brake problem with a 1995 dodge dakota

I have a 1995 dodge dakota with absolutly no brakes. I changed the master cylinder checked the lines everything is good but I still have nothing

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

Have you checked the power booster and the master cylinder> what about the wheel cylinders> have you looked at them to see if theres a leak somewhere?

Posted on Dec 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the brake master cylinder on a 2000 dodge dakota rt 360 magnum 5.9l v8 mopar


disconnect the front and rear brake lines, undo bolts holding the master cylinder to the brake booster. Bench bleed the new master and reconnect to booster and reconnect lines. Be very careful when undoing the lines from the master cyclinder as you do not want to damage them. Soak with WD-40 before loosening. Once everything is back in place you will need to bleed all calipers and/or wheel cylinders. Again soak the bleeder screws beforehand with WD-40 as they break off easily.

Dec 12, 2014 | Cars & Trucks

1 Answer

Where is1998 dodge dakota brake light switch ?


Try the brake Pedal where it pivots under dash,should be a switch with two wires or on the brake master cylinder or near by in the brake line.

Jul 21, 2014 | 1998 Dodge Dakota

1 Answer

Have a 1991 dodge dakota, have replaced everything , still cant get brakes to work.


How about the rubber flex hoses restricted

In the rear you have an abs hcu you can throw way
& bypass,then unplug the controller up under the dash
on the passenger side

Also the rear brake cables won't work for rust,they have to go also

I had a 1992 Dakota for 18 years

Leave the wire off the proportioning valve as the vehicle is wired wrong & if your bleeding it ,it will melt down the wires in the ignition switch (been there) Vehicle is not the same as the factory wiring diagrams

Mar 26, 2014 | 1991 Dodge Dakota

2 Answers

Brakes feel real soft will not stop quick if needed


You are low on brake fluid. Check your master cylinder for the fluid level and check for leaks in the line.

Nov 28, 2011 | 1987 Dodge Dakota

1 Answer

Soft (mushy) braking on my 2005 Dodge Dakota V6


soft and mushy brakes is a sign that there could be air in the brake system or your master cylinder has a bad O-ring in it.
first thing to check is to see if there is fluid in your brake fluid reservoir,, if the fluid level is low - then re-fill the reservoir and bleed the brake lines ( all the brake lines ). if the reservoir is full - then I would assume that the master cylinder is bad and needs to be replaced,, but there is also a chance that you have a leak somewhere in a line or at the distribution valve -- make sure you look for the leak.
if you are still having troubles - please feel free to write me back here and I will do my best to walk you thru the next steps needed.

c...

Feb 15, 2011 | 2005 Dodge Dakota

1 Answer

My brakes do not stop and go all the way to the floor


You 're brake master cylender has failed.
How to change it.

Use a flare wrench and remove the two brake lines.
Then remove the the two nuts that hold it to the fire wall.
Then remove.
Then remove the master cylinder reservoir because your
going to have to put it on the new one.
Drain out any brake fluid from it.
In stall the reservoir on the new master cylinder.
Now you'll have to prime the new master cylinder.
Put the master cylinder in a vise and put brake fluid into it.
Now place your fingers over the two holes that the brake line go into.
Use a large phillips screw driver and push the piston in and out about 10 times.
But, do it slowly. make shore to keep your fingers over the brake line holes. .
Now install it back in.
Remember to bleed your brake system when your done.
Hope this helps give feedback and good luck FixYa

Nov 30, 2010 | 1995 Dodge Dakota

1 Answer

How is the master cylinder replaced on a 93 dodge dakota sport 4x4 6 cyl 3.9L


use a flare wrench and remove the two brake lines
then remove the the two nuts that hold it to the fire wall
then remove.
then remove the master cylinder reservoir because your
going to have to put it on the new one
drain out any brake fluid from it
in stall the reservoir on the new master cylinder
now you'll have to prime the new master cylinder
put the master cylinder in a vise and put brake fluid into it
now place your fingers over the two holes that the brake line go into
use a large phillips screw driver and push the piston in and out about 10 times
but do it slowly. make shore to keep your fingers over the brake line holes .
now install it back in
remember to bleed your brake system when your done

Nov 22, 2010 | 1993 Dodge Dakota

1 Answer

I have a 2001 Dodge Dakota that will not lock up the brakes. Everything has been replaced and it coasts to a stop. The pedel goes to the floor at full stop . Master cyl, prop valve, new lines, and...


Master cylinter is shot is my first thought. if it has been replaced with a referb.. replace it again. make sure you bench bleed the master cylinder before putting it on.. if it's new, you have a ton of air in the lines.. bleed the pass rear first/ drivers rear/ pass front/ pass rear.. FYI your brakes/ tires should never lock up, you have ABS.

Jul 22, 2010 | 2001 Dodge Dakota

2 Answers

Brake problems! getting fluid to all lines no air in lines but pedal is almost touching the floor


Air can be a pain to get out sometimes. Check for striped fitting/bleed screws, if it all check out, it is most likely the master cylinder on the firewall.

May 01, 2010 | 1987 Dodge Dakota

1 Answer

Brake fluid leaking from the bottom of the driver side on a dodge dakota 97


master cylinder maybe or the brake lines going to the back of the truck, but most likely the master cylinder, check to see if you see any brake fluid on the front of the brake booster or any paint peeling off the brake booster

Aug 26, 2008 | Dodge Dakota Cars & Trucks

Not finding what you are looking for?
1995 Dodge Dakota Logo

Related Topics:

334 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...