Question about 1990 Ford LTD Crown Victoria

Open Question

1990 Ford Crown Victoria will not start

My problem started with my emergency brake. When the dash light stayed on with my emergency brake released, my signal lights would not work, my heater, my rear defrost, power windows and only partial dash lights would work. The headlights and taillights and brake lights would work and the engine would run, but now that it has gotten colder here in Alberta, Canada, the engine will not start, even though the battery has lots of juice. All it will do is flash the dash emergency brake light and the day date lights alternately when you turn the key on and off. I tested the battery and it is just about up to full power and I am thinking that the computer is toast. Does this problem sound familiar to other Crown Vic's that you have had experience with?

Posted by on

5 Suggested Answers

gforce3s
  • 31 Answers

SOURCE: i need a diagram for a 1998 ford crown vic interior fuse box

here ya go

463d1df.gif

Posted on Dec 11, 2008


CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

  • 1632 Answers

SOURCE: 1999 ford crown vic dash light running light problem.

Check all the bulbs at tail end for parking and brakes, test grounds and harness for trailer. Check fuses. clean batery terminals, Re instal head light swich properly and make sure all wires conect.
Vitally

Posted on Sep 09, 2009

Testimonial: "thank you for quick response will try all of your suggestions will re post if no luck."

miket756
  • 2702 Answers

SOURCE: 2000 ford focus sedan 2.0 dohc ztec engine rear

check all battery leads and earth straps
"" car body and engen bay straps""
also check battery terminals are tight check its full of battery water too if its been low for a time bump it!
and have a ""drop meeter test"" done on the battery if its a bad battery it should show that up first time it could have cracked plates inside the battery its self, test by turning on head lights then hit starter, if every thing go's dead!!!! put ""good jump start"" battery on to car and try it again,,, all should work just fine then,,,,it could just be a flat battery?????

Posted on Oct 27, 2009

  • 234 Answers

SOURCE: '96 ford Crown Victoria....No hazard or brake light no turn sigal

Sounds like the multifunction switch. Try working the hazard switch up and down a few times to see if you get some lights to work. If so then replace the switch.

Posted on Nov 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 crown victoria, headlights, blinkers, brake lights and emergency flashers quit all at once


May be your multi function switch( directional switch),possibly a bad fuse,a LCM (lighting control module,a black box by the gas pedal,or maybe a plug pulled out of the module for some reason.

Oct 26, 2013 | 1997 Ford Crown Victoria

1 Answer

No head light turn lights brake lights dash lights inside light


yes you should also look in the owners manual and see if theres any relays that could be blown

Mar 20, 2013 | 2003 Ford Crown Victoria

1 Answer

I have a 1990 Crown Victoria LTD, it started sputtering at low speed. Then stalled and won't start now. Any ideas?


You will have to start a diagnosis. Starting with the small test then on to others. 1. Getting gas to carberator 2. Pull coil wire and verify firing.

Feb 19, 2012 | 1990 Ford LTD Crown Victoria

1 Answer

Brake light wont work on police interceptor 2004 victoria


First check fuse for brake light with test light if fuse is good test brake light switch under dash with test light if you dont understand how to do the above contact me at Ken17402@msn.com title the message crown vic problem

Nov 15, 2010 | 2004 Ford Crown Victoria

1 Answer

01 Crown vic will not stay crunk


get the auto choke operation checked,or a good tuneup

Jul 08, 2010 | 2001 Ford Crown Victoria

1 Answer

Emergency brake locked after pull release handle


handbrake jammed on somewhere ,could be front cable ,because the rear cable is pulled by the compensator so if it was the rear one then i would expect only one cable siezed and that is normally the kerbside one.

Oct 23, 2009 | 1995 Ford Crown Victoria

2 Answers

HOW TO REPAIR 1990 CROWN VICTORIA THAT JERKS WHEN GOING UP A INCLINE. THERE IS A TRANSMISSION FLUID LEAK.


need more info it could be fuel pump as well as the transmission make sure trans. fluid is on the right level

Jul 09, 2009 | 1990 Ford LTD Crown Victoria

1 Answer

My brakes lights wont work! bulbs are fine! just dont know what fuses are which!


if your 1990 ford LTD is anything the same as my 1989 ford LTD then your fuse is in position "4" on the fuse panel

Apr 16, 2009 | 1990 Ford LTD Crown Victoria

1 Answer

Good brakes. first time, second hit solf.


try to flush all the brake system if its stay same u have to change the brake master cylinder

Mar 22, 2009 | 2003 Ford Crown Victoria

Not finding what you are looking for?
1990 Ford LTD Crown Victoria Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...