a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
It will be located on the rear of the transmission. I am not sure if it will be on the transmission or on the transfer-case but it should be in that general location. I have attached a pic of a new sensor to help you locate it
This is the part you will see
The transmission sensor or speed sensor is located in most vehicle located on the transmission case.These speed sensors are driven by a gear located on the output shaft. The speed sensor's driven gear can be either machined or fastened by a clip. The driven gear is made by plastic to make it softer than the drive gear. It's located on the end of the vehicle speed sensor.
Ther are more than one type of speed sensor for jeeps....I am chrysler jeep tech...there are 2 speed sensors on the trans and also speed sensors at the wheels (IF IT HAS ABS)...Normally the engine speed is done by an IAC Motor...If you are meaning idle...Can you send more information....
Also you may have a vacum leak..........You have an Input speed sensor and an output speed sensor ....Do you know exactly which it is ....Both are at transmission /If 4 wheel drive see transfer case also.I have the manual at my fingertips and will be glad to assist you with any problems............................I can help................metalpoet
LEVEL CHECK -manual transmission
The vehicle speed sensor (speedometer gear), which is located on the transaxle, serves as the manual transaxle's dipstick.
Park the car on a level surface, turn the engine OFF and apply the parking brake.
Locate the speedometer cable assembly where it enters the transaxle.
Unplug the electrical connection from the vehicle speed sensor (speedometer gear).
Disconnect the speedometer cable from the speed sensor.
Wipe the area around the speed sensor with a clean rag, then loosen the speed sensor retaining bolt.
Gently pry the speed sensor from the transaxle.
Fig. 1: Location of the manual transaxle's fluid level marks — 1.8L engine
Fig. 2: Location of the manual transaxle's fluid level marks — 1.9L and 2.0L engines
Check the condition of the speed sensor O-ring and replace it if it is damaged.
Check the fluid level on the speed sensor as illustrated.
If the level is low, place a funnel in the speed sensor hole.
Add the specified fluid to the transaxle until the FULL level is reached. Do not overfill the transaxle.
Install the speed sensor and tighten the retaining bolt to 69–104 inch lbs. (8–12 Nm).
Connect the speedometer cable.
Engage the speed sensor electrical connection.
Fig. 3: If necessary, add transmission fluid through a funnel into the speed sensor opening
hi , their is two different speed sensors on your vehicle one is the input speed sensor which is inside the transmission and the transmission will have to be removed to replace it the other one s the output speed sensor is located directly above the passenger side trans-axle shaft. your input sensor is the sensor which tells the transmission when to shift and the output speed sensor tells the speedometer what it should display and both those parts are fairly cheap they are around 15-25 dollars but just remember if your input speed sensor is bad it is gonna cost you a minimum of 1000 dollars to have a mechanic fix as the transmission needs to be removed hope this is what you needed
There are two speed sensors one is called a revolution sensor that is located on the case of the transmission. You can take the driver side wheel off and see the sensor on the top of the case of the transmission. A 10mm bolt is holding it in. Easy fix