Question about Hyundai Motor 1998 Accent

1 Answer

How do you remove the rotor on a accent gs 1998

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 566 Answers

Hi from the uk to remove the rotor(brake disc) is as follows= raise and spport car safely ! then remove wheel then remove the two bolts at rear of brake caliper these are the bolts that secure caliper to the carrier then if you pull on the rear of caliper away from carrier it will push the brakepad and piston back sufficiently to remove caliper ? tie up caliper so as to protect flex hose from strain ok? then there are two larger bolts 17mm ??spanner that hold the carrier and secures it to the stubaxle assy at the rear remove these bolts and carrier ok? now the rotor is secured to the hub by 2 posidrive or torque head screws unscrew and then you may have to tap the rotor from behind to remove ? re assembly is the reverse of above ok? now whilst stripped down may i suggest you wire brush caliper and carrier assys of rust etc then to prevent rust again i myself paint the carrier and the outside surface of caliper with hammerite quick dry paint or they do a spray paint if yo prefere? dries 15--20 minutes and red always looks great? like customised ??you might think its bulls---t but customers are always impressed and think new calipers fitted ? however back to finished job now when you have reassembled and b4 fitting wheel pump the brake pedal! then bleed the caliper to clear/flush out old fluid untill clean fluid appears a couple of pumps of pedal will be suffice dont forget to top up reservoir with fluid hope this all helps and is clear instructions for you wish you well and a happy new year 2009 ! ps e mail me direct if you req further info/advice and please update how you get on?

Posted on Dec 28, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the cam sensor 2002 hyundia accent 1.5?

    More images for Where is the cam sensor 2002 hyundai accent 1.5

    Hyundai Crankshaft Position Sensor Removal - YouTube

    ? 3:42
    Jul 12, 2012 - Uploaded by richpin06a
    Hyundai Elantra Crankshaft Position Sensor Removal.

    Hyundai accent 2001 - YouTube

    ? 2:44
    Nov 25, 2012 - Uploaded by mig dups
    2000 Hyundai Accent GS turns over - no start. ... HyundaiCrankshaft Position Sensor Replace Timing Belt ...

Dec 26, 2015 | Cars & Trucks

1 Answer

W/shield washer reservoir replacement on 2007 Hyundai Accent

if the same design as 2004 Accent then just remove right front wheel, slide underneath, and start wrenching on it. should be 2 or 3 bolts

Feb 08, 2013 | 2007 Hyundai Accent GS Hatchback

1 Answer

Replace 2007 accent washer fluid reservoir

if same as 2004 Accent, then remove right front wheel, slide underneath, and start wrenching. should be 2-3 bolts

Jan 30, 2013 | 2007 Hyundai Accent GS Hatchback

1 Answer

02 Hyundai Accent GS, Does horn actually need a relay to operate? Lifted fuse box to check, suddenly there is no relay. And didnt remove, yet horn stopped working. Tried external switch, wiring INTO the...

I actually have the same problem. I replace the actual horn but admittedly wit a new one. Want to try the relay first but cannot get it to come out or find the new one.

Aug 16, 2011 | 2007 Hyundai Accent GS Hatchback

1 Answer

How do you remove Driver's Side ( RH drive) tail

If it doesnt have a acsess panel to remove in the trunk you will have to pull carpet cover back to get acsess to plastic wingnuts or bolts holding it in. Hope this helps

Jun 19, 2011 | 2001 Hyundai Accent

1 Answer


The GS is equipped much like the GLS sedan, with some equipment deleted for a base ... trim level has been introduced for the Accent with a base price of only US$9970. The Accent Blue is only available as a 3-door hatchback with a manual

Dec 12, 2010 | 2007 Hyundai Accent GS Hatchback

1 Answer

Where is the backup light switch located for 1998 Hyundai Accent GS

On the gearbox. this is easy to find but requires 2 people as there is 2 or 3 plugs on the gearbox. put the vehicle in reverse and turn ignition on, DO NOT START! remove one plug at a time from the transmission while someone stands at the rear of the vehicle and lets you know when the reverse lights go out.

Jul 18, 2010 | Hyundai Motor 1998 Accent

1 Answer

Brake rotors for hyundai accent

The rotor is mounted to the hub by 4 bolts. The procedure is described in the service manual. Go to and register. You'll have access to the information you want after you register (shop manual, wiring diagrams, service bulletins, etc.).

May 28, 2009 | 2006 Hyundai Sonata

1 Answer

Where are the spark plugs on a 2009 hyundai accent located ?

You have to remove the oil filler cap and then remove the fancy black plastic cover which is labeled "DOHC 16V" and which has the Hyundai emblem on it.

Apr 12, 2009 | 2007 Hyundai Accent GS Hatchback

Not finding what you are looking for?
Hyundai Motor 1998 Accent Logo

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides