Question about 2004 Chevrolet Silverado 2500HD

3 Answers

1976 chevy 3/4 ton 4x4 won't turn over

The truck has ran like a champ for the 2.5 years i've owned it. friday
12/26 i parked it for about an hour, tryed to start it and it clicked once and then nothing. i jumped it and got nothing. i'm stumped i need help please.

Posted by on

  • hawnt70 Dec 28, 2008

    did check all conections. the lights and raido come on. the voltmeter shows about 12 volts. bad starter?

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check the fueable link

Posted on Jan 20, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check both cables first if they are good have battery tested at auto parts you can loose a cell fast.

Posted on Dec 31, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check the ground wire to the frame from the battery

Posted on Dec 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can i find a emision diagram for 1976 chevy 2 ton v8?


  • Hi Sanjuana:
  • 1976? There really wasn't a lot of emission control associated with engines back then.
  • What engine size is it? I'll try to dig up some info for you.
  • Please reply as a comment to this post.
  • cheers.

Nov 19, 2015 | Cars & Trucks

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle


QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)



see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

1 Answer

Wiring diagram 1976 chevy 3/4 ton van


Disconnect the small purple wire at the starter and see if that stops it. If not, replace the starter. If it does you will have to test the rest of the starter circuit.

Aug 18, 2013 | Cars & Trucks

1 Answer

Need a diagram of 1999 chevy 1/2 ton 4x4 rear brake brackets


Go to you nearest auto part. Store. They will print one up for you or when you get the kit it will diagram with it

Mar 06, 2013 | 1994 Chevrolet K1500

1 Answer

CODE P0101 AND CODE P0341 i have a 96 chevy blazr 2dr 4x4 4.3L. I RECENTLY HIT A LARGE BUMP AND THE TRUCK STALLED.PULLED OVER AND STARTED IT BACK UP .IT RAN A SECOND OR TWO THEN STALLED AGAIN. IT WASN


Well the code 101 is for the MAF sensor and code 341 is for the cam sensor if equipped.
I'm showing a distributor for that engine so its possible something is going on inside of it.
My first guess would be something in the engine harness that was jarred loose.
You might have to test the circuits at the ECM to see if anything is not making the circuit back to it.
If the engine won't idle and the MAF code is present, you could have a large vac leak somewhere.

Jul 10, 2012 | 1996 Chevrolet Blazer

1 Answer

Own a 2002 Chevy Malibu - the digital clock has to be reset after car has been parked (i.e. a few hours to overnight) what is wrong?


this problem can cause of two things one is clock need three wire connection 1 all time +ve 2 +ve only when ignition switch is on 3 earthing. for this problem if 1 no wire all time +ve is disconnected from clock . or it is problem with clock you have to repalce it if 1 no wire is connected properly.

Sep 06, 2010 | 2002 Chevrolet Malibu

1 Answer

I have a '97 Chevy 1/2 ton 4x4 PU. Very good


Sounds like a loose connection, Clean the fuse contacts. Sometimes lubricant and dirt gets on the contacts within the switch itself and this will interfere with power supply. Have you checked the wiper relay corrosion and wear on the relay contacts impair electrical connection. Brighten up contacts with fine sand paper and if the relay contacts are suspect, remove the cover and draw folded sand paper between the contacts until clean.

May 13, 2010 | 1994 Lincoln Town Car

1 Answer

1990 3/4 ton chevy 4x4 wont engage


the accuator is proby weak and working under pressure!!!!!

Jan 15, 2010 | 1991 Chevrolet K2500

1 Answer

I lost park every thing else works just fine i have a 1983 chevy 3/4 ton 4x4??


disconnect the linkage at the transmission and put it in park.if it does not lock,the pin inside the transmission is broken

Nov 05, 2009 | 1983 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

329 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...