Question about 1998 Chevrolet Cavalier

2 Answers

Blower motor installation and location

I need the location and installation for the blower motor

Posted by on

  • Anonymous Mar 16, 2014

    Image of location please

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 379 Answers

Location is right side under dash , procedure is remove right sound insulator , disconnect blower motor connectors , remove blower motor cooling tube , remove the blower motor screws and blower motor , and reverse procedure to install .thanks.

Posted on Dec 30, 2008

  • Rick Byrd
    Rick Byrd Jan 03, 2009

    follow up - was this information worth a FIX YA vote ? thanks for voting ! .

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If my blower moter stops blowing. does this always mean the blower is bad?

Posted on Jan 06, 2009

5 Suggested Answers

  • 1 Answer

SOURCE: locating heater blower motor resistor

the resistor is behind your glove box. open the box and push in the sides to release it and let it hang down...the resistor is right there. I didn't try to replace it, a friend did it, but the part was under $20.

Posted on Feb 01, 2009

  • 784 Answers

SOURCE: location of blower motor fuse

Fuse blower motor is not in the fuse box. It is located outside. lOpen the hood, on the driver side near the fender, about 1 feet from the fuse box toward the direction of the radiator, there is a retangular about 1x2 in with wire coming out from each end. Snap it open, inside is the the wire fuse.

Posted on Aug 05, 2009

  • 2 Answers

SOURCE: location on a 323i bmw station wagon blower motor resistor

please help me with location of this blower resistor n 64116923204in the bmw 318 i tank you.tonitoneves@hotmail.com

Posted on Aug 30, 2009

airjer995
  • 5332 Answers

SOURCE: 98 century heater blower motor resistor location

look under the passenger side of the dash. There will be a plastic trim panel that will need to be removed. Once its out of the way you will see the blower motor. The resistor will be just to the drivers side of the blower motor.

Posted on Nov 15, 2011

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need information on how to change my blower motor assembly on a 2001 jeep grand cherokee laredo 4x4 4.0


The blower motor is located under the right side of the dash in the A/C Heater housing. Disconnect blower cooling hose. Remove blower connector from retainer and unplug the connector. Remove the 3 blower motor screws and remove blower motor. Reverse procedure to install..


dttech_128.gif


dttech_129.gif

Jun 30, 2011 | 2001 Jeep Grand Cherokee

2 Answers

I need to locate my blower motor resistor on my 1999 S-10. do u know where it is located on my s-10?


The resistor is located under the hood on the passenger side. At the back of the engine compartment you need to locate the airbox it can be identified by a circular piece that's right beside the fender on the firewall (this is your blower motor) to the right if it (looking from the front of the truck) about 4 -6" you will see a wire plug. Unplug this connector and locate the four screws that attach it to the air box. Remove these screws and pull the resistor from the housing.

Hope helps (remember to rate this answer).

Dec 13, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

Hi, i need to remove and replace the blower motor for the a.c./ heater, and dont know where it is located. can you please help?


Blower Motor Removal & Installation To Remove:
  1. Remove the insulator from under the right side of the dash.
  2. Disconnect the electrical connector from the blower motor.
  3. Remove the blower motor retaining screws.
  4. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting screws.
  3. Connect the electrical connector to the blower motor.
  4. Install the under dash insulator.
prev.gif next.gif

Dec 10, 2010 | 1999 Pontiac Grand Prix

1 Answer

Need to replace heater blower motor. How do I get to it?


Behind the glove box. Please see my tip at http://www.fixya.com/cars/r6234839-doesn_t_heater_or_air_conditioner_blow . These are generic instructions. If you get stuck, please get back to me.

See instructions from autozone.com below.


REMOVAL & INSTALLATION


With Air Conditioning
See Figures 1, 2 and 3

  1. Disconnect the negative battery cable.
  2. Remove the glove compartment door and glove compartment.
  3. Disconnect the blower motor wires from the blower motor resistor.

jturcotte_62.gif
Fig. Fig. 1: Disconnect the blower motor wires from the blower motor resistor-1988 Escort
  1. Loosen the instrument panel at the lower right-hand side prior to removing the motor through the glove compartment opening.
  2. Remove the blower motor and mounting plate from the evaporator case.
  3. Rotate the motor until the mounting plate flat clears the edge of the glove compartment opening and remove the motor.
  4. Remove the hub clamp spring from the blower wheel hub. Then remove the blower wheel from the motor shaft.
jturcotte_63.gif
Fig. Fig. 2: Unbolt the mounting plate from the case


jturcotte_64.gif

Fig. Fig. 3: The motor can now be removed from the case


To install:

  1. If removed, assemble the blower wheel to the motor shaft and install the hub clamp.
  2. Install the motor and blower wheel assembly.
  3. Secure the instrument panel at the lower right-hand side.
  4. Connect the blower motor wires at the blower motor resistor.
  5. Install the glove compartment door and the glove compartment.
  6. Connect the negative battery cable.
  7. Check the system for proper operation.

Without Air Conditioning

  1. Disconnect the negative battery cable.
  2. Remove the air inlet duct assembly.
  3. Remove the hub clamp spring from the blower wheel hub. Pull the blower wheel from the blower motor shaft.
  4. Remove the blower motor flange attaching screws located inside the blower housing.
  5. Pull the blower motor out from the blower housing (heater case) and disconnect the blower motor wires from the motor.

To install:

  1. Connect the wires to the blower motor and position the motor in the blower housing.
  2. Install the blower motor attaching screws.
  3. Position the blower wheel on the motor shaft and install the hub clamp spring.
  4. Install the air inlet duct assembly and the right ventilator assembly.
  5. Connect negative battery cable.
  6. Check the system for proper operation.

Nov 05, 2010 | 1989 Ford Escort

2 Answers

Where is the a/c blower motor located on my 1997 pontiac sunfire?


prev.gif next.gif HEATING AND AIR CONDITIONING Blower Motor REMOVAL & INSTALLATION Fig. 1: Remove the sound insulator from underneath the passenger side of the instrument panel 91146p69.jpg
Fig. 2: Remove the retaining bolts for the blower motor assembly 91146p61.jpg
The blower motor and fan are serviced as an assembly only.
  1. Disconnect the negative battery cable.
  2. Remove the passenger side sound insulator.
  3. Detach the electrical connections from the blower motor.
  4. Remove the blower motor retaining screws, then remove blower motor and fan assembly. To install:
  5. Install blower motor and fan assembly, then secure using the retaining screws.
  6. If equipped, connect the blower motor cooling tube.
  7. Attach the electrical connections to the blower motor.
  8. Install the right side sound insulator.
  9. Connect the negative battery cable.

Aug 03, 2010 | 1997 Pontiac Sunfire

1 Answer

I need to replace the heater a/c blower motor, how do I.


Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect battery negative cable from remote negative terminal on shock tower and properly isolate to prevent accidental reconnection.
  3. Remove or disconnect the following:
    • Glove box assembly
    • Joint duct
    • Resistor
    • Blower fan and motor
    • Air changeover damper motor
    • Blower assembly
To install:
  1. Install or connect the following:
    • Blower assembly into duct
    • Air changeover damper motor and reconnect the electrical plug

    NOTE Lubricate the damper motor's slide contacts with multi-purpose grease

    • Blower fan and motor into the plenum and reconnect the electrical plug
    • Resistor on the joint duct
    • Joint duct to blower assembly
    • Glove box assembly
The blower motor is located on the right side of the heater housing.
  1. Disconnect battery.
  2. Remove the lower right under panel silencer duct.
  3. Remove the blower motor connector from resistor block.
  4. Remove the blower motor case retaining screws.
  5. Lower blower motor case from housing
  6. Remove the fan scroll from motor shaft.
  7. Remove the motor from motor case.

68654d5.gif
Blower motor (1)

To install:
  1. Install the in reverse order of removal.

Jan 19, 2010 | 2000 Dodge Stratus

1 Answer

Replace heater blower motor 96 neon


With Air Conditioning
  1. Disconnect the negative battery cable.
  2. Remove the right side scuff plate.
  3. Pull back the carpet from the passenger's side floor.
WARNING Be careful not to cut into the blower motor wiring!

  1. Use a suitable utility knife to cut the wheel housing silencer in line with the blower motor wiring.
  2. Detach the blower motor electrical connector.
  3. For right-hand drive vehicles, remove the motor cover.
  4. Unfasten the three blower motor retaining screws, then lower the blower motor assembly from the unit housing.

3efc4db.gif
The blower motor assembly is located under the passenger's side dash panel


c91626e.gif
Blower motor mounting and location of the retaining screws and wiring-vehicles with A/C

To install:
  1. Raise the blower motor into position in the unit housing and secure with the three retaining screws.
  2. If removed, install the motor cover.
  3. Attach the blower motor electrical connector.
  4. Use tape to secure the silencer into position.
  5. Reposition the passenger's side floor carpeting.
  6. Install the right side scuff plate.
  7. Connect the negative battery cable.

Oct 25, 2009 | Chrysler Neon Cars & Trucks

1 Answer

HOW DO YOU CHANGE THE HEATER BLOWER MOTOR?


YOU NEED TO TURN OFF RADIO TO KEEP FROM LOSING RADIO CODE.REMOVE NEGATIVE BATTERY CABLE.THAT WILL DISABLE AIR BAGS.WAIT 30 MINUTES.SO THE AIR BAGS CAN DISCHARGE.THE BLOWER MOTOR IS LOCATED ON THE PASSENGER SIDE OF VECHICLE UNDER THE INSTRUMENT PANEL.WHEN REPLACING THE BLOWER MOTOR.YOU HAVE TO REMOVE THE SQUIRREL CAGE OR BLOWER MOTOR FAN.BY REMOVING THE METAL STAR CLIP RETAINING THE FAN CAGE TO THE MOTOR SHAFT.REMOVE THE FAN BY PULLING STRAIGHT OUT.TO INSTALL BLOWER FAN TO NEW BLOWER MOTOR.INSTALL THE FAN CAGE ONTO THE MOTOR SHAFT .ADJUST THE FAN CAGE TO GET A CLEARANCE OF 0.30 INCH TO THE MOTOR MOUNT PLATE.INSTALL EVERYTHING VISA VERSA.BESURE TO BUY A REPAIR MANUAL.SO IT CAN SHOW YOU WHERE ALL YOUR PARTS AND SCREWS ARE LOCATED. WARNING IF YOU HAVE ANY DOUBT ABOUT THIS TASK.LET THE DEALERSHIP DO IT.

Oct 13, 2009 | 2005 Chevrolet Impala

2 Answers

Blower for Heat/A/c not working


Blower Motor Resistor Replacement Removal Procedure
  1. If equipped, remove the IP sound insulator.

  2. 476821.gif

  3. Disconnect the electrical connection from the blower motor.
  4. Disconnect the electrical connection from the blower motor resistor.

  5. 382493.gif

  6. Remove the blower motor resistor retaining screws.

  7. 382503.gif

  8. Remove the blower motor resistor.
Installation Procedure

    382503.gif
  1. Install the blower motor resistor.

  2. 382493.gif

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the blower motor resistor retaining screws.
  4. Tighten
    Tighten the screws to 1.6 N·m (14 lb in).

    476821.gif

  5. Connect the electrical connection to the blower motor resistor.
  6. Connect the electrical connection to the blower motor.
  7. If equipped, install the IP sound insulator.

Dec 08, 2008 | 2001 Chevrolet Silverado 1500

Not finding what you are looking for?
1998 Chevrolet Cavalier Logo

Related Topics:

987 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...