Question about 2000 Chrysler LHS

2 Answers

Driver side power window motor not working

How do I change power window motor 2000 chrysler lhs? How do you know if a new regulator is needed

Posted by on

  • fightk Dec 31, 2008

    I was able to change out the unit using yor instructions.It took some time but I won the battle.

    Thanks for your help.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 46 Answers

I would buy a Chilton for your car, but I own an Intrepid and the process is pretty dangerous. First of all, if you're not getting power to the motor, a new motor won't help. Also, if the weather stripping is sticking, this will make lowering the window hard. If it is and you need to replace the motor, clamp the regulator into position with vise grips or a C-clamp (This is keep the window from falling down). The motor should just unbolt from the regulator at this point. Again, this is extremely dangerous as the motor holds the regulator in place. You can lose fingers or other body parts trying this stunt. I accept no responsibility for injuries or death, so be careful.

Posted on Dec 28, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 56 Answers

If indeed you need to replace the motor be prepared for a long day. almost all the newer cars now a days are fused together with the regulator and motor as one unit. first you must take the door panel off and it helps to have some tape handy like duck tape or box tape. if you can move the window at all try to get it about 3 inches from the top and put tape on the window over the door frame inside to outside to keep the window from dropping when you take it apart. when removing the door panel be careful not to yank the wires attached to switches. disconect the wires to the outer panel and put flat someplace safe. most likely it will be 7/16 or 1/2 size nuts or bolts holding the unit together. locate and remove these. also the window glass that is attached to the arm of the regulator. once thes are loose slide the entire unit out of the hole in the door. sometimes this is complicated as you may have to twist the unit in about 50 directions just to get it out. once it is out do just backwards to put a new one in. hope this helped.

Posted on Dec 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of crankshaft sensor on a Chrysler lhs


Passenger side of motor bottom by transmission housing. Hard to get to from top of motor but not impossible.

Sep 09, 2014 | 2000 Chrysler LHS

2 Answers

I need the regulator for drivers side electric window


advance auto parts Dorman - HD Solutions Power Window Regulator and Motor Assembly Part No. 741-5202 Warranty Be the first to write a review ' View Customer Q&A $107.99

Apr 07, 2014 | 1992 Chrysler New Yorker

1 Answer

Drivers side power window quit working The word auto on the switch is still lit up though. 2004 Chrysler Sebring


If you can hear the window motor when you push the button you need a new window regulator.

Dec 12, 2010 | 2004 Chrysler Sebring

1 Answer

My driver side front window does not come down but the passanger side front and back and driver back do go up and down. Do i need to change the power window motor or is it the window regulator for driver...


regulator usually wears out and breaks or gets bound and burns up motor, change them both if available. Good sign of bad regulator is sloppy window in track, or window off track. I always replace them together if they are available. it is possible that you just need a switch, but most likely the reg/motor.

Apr 15, 2010 | 2000 Daewoo Nubira

2 Answers

2000 dodge durango driver side window problem


I have had to replace three of the four window power regulators in my 2000 Durango. They just seem to stop working within a year or two of each other.

Aug 02, 2009 | 1999 Dodge Durango

1 Answer

Both driver and passenger side power windows don't work


yes they are two different pieces,why do you ask

May 19, 2009 | 1998 Chrysler Town & Country

2 Answers

Where is the starter on a 2000 chrysler lhs?


I can't tell you what side it's on.... but it is where the motor joins to the transmission. if it is front wheel drive (the motor is sideways). look down about the middle of the engine where it joins the transmission.... that is your starter. you should be able to follow one of the large wires from the battery to it. speaking of which make sure you disconnect the battery before changing the starter.

Apr 15, 2009 | 2000 Chrysler LHS

1 Answer

Need instructions on changing drivers side 2000 Yukon/new style window regulator. Have the new part, just need instructions.


i have replaced all four window motors on my 2000 yukon. I actually did the passenger side front today. It was a nightmare! if you don't have the the cables set right when you install the new motor/regulator it won't work right and it becomes extremely difficult to set right. I suggest having someone do it for you if you are not patient and handy. if u do go for it make sure u lay it out flat and upside down so the screws are facing u from the motor/regulator and do ur best to make sure that the cables are exactly where they were when u took off the old regulator/motor. this is again very difficult. took me about 4 hours and got very sunburnt on my neck! I am not a mechanic but a do it yourselfer. Last time I did the driver side i had a mechanic give me a hand and it took about an hour. Also make sure you wedge the window in with a stick or screwdriver so it won't drop while working on the door. If it is the cables u are replacing it is the same project. they are all interlinked. good luck and hope this helped.

Mar 22, 2009 | 2000 GMC Yukon

Not finding what you are looking for?
2000 Chrysler LHS Logo

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...