Question about 2001 Chevrolet S-10

2 Answers

Lino1973 Hi, about my 2001 s10 with stuck on 4lo, I press the 2hi and the 4hi bottons but nothing happens...please advise

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hallo ik heb het zelfde probleem gehad. Kreeg eerst storing met knipperen en ging automatisch terug naar 2h. Daarna deed hij helemaal niets meer. Ik heb de stekker van de 4wd computer schoon gemaakt. Deze was aan het roesten. Alles werkt weer perfect.
De computer vind je rechts bij het voor portier passagier kant.

Posted on Jan 11, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 78 Answers

You might have a bad transfer case servo motor,or vacume switch(on t-case)
a scanner at an aoutoshop will tell!

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 chevy suburban stuck in 4 lo anyone out that cant help


Put truck in Neutral while key in run position engine off or on (doesn't matter which). If it's pushbutton 4wd then try hitting 4low again. if that doesn't work some of the chevy trucks required you to press 4hi to get into 4high and then press 4hi again to get back to 2hi, unless yours has a 2hi button. In that case press 4hi to get into 4high and then press 2hi to get back to 2wd. either way you need to be in neutral to get out of 4lo. I have shift on the fly (Mechanical Shifter on floorboard for transfer case) on my 1990 Suburban and still have to put it in neutral to get out of 4lo. Good Luck.

Jan 30, 2014 | 2000 Chevrolet Blazer

1 Answer

How to properly engage and dis-engage 4 wheel drive 0n 1996 gmc sierra


  • Shifting from 2HI to 4HI Press and release the 4HI button. This can be done at any speed, and the front axle will lock automatically.

  • Shifting from 4HI to 2HI Press and release the 2HI button. This can be done at any speed, and the front axle will unlock automatically.

  • To shift from 2HI or 4HI to 4LO, the vehicle must be stopped or moving less than 3 mph with the transmission in NEUTRAL

  • Hope this helps.

Oct 29, 2011 | 1996 GMC Sierra

1 Answer

How do i know when it is in 4x4 . where must the lever be for it not to be in 4x4. no the lever is has got 2lo, 2hi n 4lo and 4hi. when you drive where must the it be, and is there lights on the bash that...


Hi, 2hi is your normal driving selection, this is NOT in 4WD mode. Both 4lo and 4hi is for 4 wheel driving, 4lo is used in extreme conditions and will gear the vehicle down to a very slow speed with maximum traction at the wheels, 4hi is for general 4 wheel driving in rough terrain, if you have lights on the dash than it will come on when you change gears, hope this help

Feb 16, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Electronic tranfer case switches are not working, what could be the problem? The vehicle is in 2 wheel hi now and when I push the 4 hi button nothing happens...when I start the vehicle, all three switches...


check the trasfercase shift control module and wiring
it's located on the passenger side
remove the carpet thresh hold
remove the kick pannel they are held on by clips
the module is behind the kick pannel
disconnect the module harness and see if it is corroded if so you need to replace the connector and the module
let me know if thats not it but i have done lots

Dec 23, 2009 | 1997 Chevrolet S-10 Pickup

3 Answers

HOW DO I PUT A 1998 GMC JIMMY IN 4 WHEEL DRIVE?, DO I HAVE BE IN "PARK" OR CAN I CHANGE IT INTO 4 WHEEL DRIVE WHILE IM DRIVING?


You should be able to put in 4x4 while in drive less than 35mph. Mine had a switch to turn to engage or dis-engage.

Oct 15, 2009 | 1998 GMC Jimmy

1 Answer

On my 2000 chevy S10 blazer, when I push the 4HI button, the 4HI and 4LO buttons flash a yellow light and it won't shift to 4WD, stays in 2HI and the light in the 2HI button is on yellow......I hear...


vacuum leak or vacuum locker solenoid problem. a great way to check for both is to remove both vacuum lines from the solenoid (located on firewall above destributor), and put a connector between them, push the button on the dash and see if it locks in.

Jan 18, 2009 | 1999 GMC Jimmy

4 Answers

2001 s10 pickup transfer case wont go out of 4lo


something has broke inside the transfer case keeping it from going into any other gear

Jan 03, 2009 | 1999 Chevrolet S-10 Pickup

2 Answers

S10 pickup 4wheel drive wont shift from 4hi to 2hi


A good ground is very imporant on these vehicles

Dec 31, 2008 | 2000 Chevrolet Blazer

2 Answers

4wd stuck in 4Lo


it is either the control switch or the actuator. look if light is flashing on push button switch. if so it is stuck. you can check actuator on front axle, to watch and see if it is moving.

Dec 06, 2008 | 2001 Chevrolet Tahoe

Not finding what you are looking for?
2001 Chevrolet S-10 Logo

Related Topics:

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...