Question about 2004 Chrysler Pacifica

1 Answer

Power Control Module

Where is the Power Control Module on my 04' Chrysler Pacifica?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 363 Answers

Open the hood and look on the left fender well, it should be a square black box

Posted on Jul 24, 2009

6 Suggested Answers

  • 55 Answers

SOURCE: Chrysler Pacifica - Cruze Control

There is no cruise relay

Posted on Oct 18, 2008

emissionwiz
  • 61249 Answers

SOURCE: Location of ignition control module on 85 Chrysler Fifth Ave.

it is on the firewall in most models, here is picture

d93987c.jpg

Posted on Oct 21, 2009

  • 1 Answer

SOURCE: location of map sensor on 04 chrysler pacifica

Sensor is located passenger side of the intake and mounts facing the firewall .It takes a torx bit to remove .NOT a philips as screw is hard to see from the front.I use a bit with a 1/4 in socket as a full size screwdriver will not fit.Remove screw and use a set of pliers to twist and pull back.

Posted on Mar 24, 2010

  • 46 Answers

SOURCE: I have a 2004 Chrysler Pacifica

136266353that would be your HO2 sensor. It's located in the left hand exhaust manifold closer to the top of the engine. It usually takes a special socket to remove one. If you have any doubt, take it to a shop and have them replace it for you. This sensor effects fuel and driveability, don't go to long without fixing it as it may cause damage to your catalytic convertors.

Posted on May 31, 2010

  • 120 Answers

SOURCE: where is the alternator located

The alternator is hiding under the engine cover. You must remove the engine cover if you have one. Locate the power steering fluid resevior. The alternator is right behind it.

Posted on Oct 25, 2010

  • 2386 Answers

SOURCE: how to bleed 04 chrysler pacifica power steering

You don;t need to its self bleeding system

Posted on Nov 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

05 chrysler 300 Wipers,turnsignals, horn and high beam headlamps don't work after battery replacement any common causes ?


Don't let it throw you because this is a Chrysler Pacifica in this video . a Chrysler is a Chrysler . All the thing's not working on your vehicle are because of one of two thing's , a bad ground or the TIPM - totally integrated power module. So check out this video ! Chrysler Pacifica TIPM Electrical Problems

Feb 14, 2016 | Chrysler Cars & Trucks

1 Answer

Turn signal stays on a2006 jeep commander


Your turn signals are controlled by a electronic control module .The integrated power module . The switch is off an the turn lamp stays on ? No Low Beam Head Lamp Chrysler Pacifica Check out this guy's video , I know it's no same vehicle as yours ,but it's a Chrysler an jeep is the same manufacture. Chrysler Pacifica TIPM Electrical Problems .

Nov 30, 2015 | 2006 Jeep Commander

1 Answer

Power control module


no, probably headlight switch which does multi functions also

Oct 23, 2013 | 2004 Chrysler Pacifica

1 Answer

What the code for a 2005 pacifica internal control module? My check engine light is staying on also.


internal control module? thats a new one for me. you need to have you obd2 scanned to find out what the trouble code it (thats why your check engine light is on)

Mar 13, 2012 | 2005 Chrysler Pacifica

1 Answer

My 04 pacifica radio, heater, dvd won't play, no


Check your relays the accessory relay right hand upper corner and the run relay middle left side if they are the same relay switch them and see if that works if not could be the body control module. Realys under hood to the right of the battery

Nov 13, 2011 | 2004 Chrysler Pacifica

1 Answer

I have a 04 chrysler pacifica and the heater was blowing non stop for a while even when car was off. and now the front doesn't blow at all but i can still control the back


there is a relay behind the glove box ours was doing ther same thing and i replaced and it solved the problem. it cost right around seventy dollars at auto zone

Oct 26, 2011 | 2004 Chrysler Pacifica

1 Answer

How to bleed 04 chrysler pacifica power steering


You don;t need to its self bleeding system

Nov 18, 2010 | 2005 Chrysler Pacifica

1 Answer

Where is the alternator located in the chrysler 04 pacifica/


The alternator is hiding under the engine cover. You must remove the engine cover if you have one. Locate the power steering fluid resevior. The alternator is right behind it.

Oct 24, 2010 | 2004 Chrysler Pacifica

1 Answer

Serpentine belt diagram for 2004 chrysler pacifica


Try this picture, it is a little hard to see, but if you have a program on your computer like power point copy and paste it to a frame and you can enlarge it to see better

http://media.photobucket.com/image/04%20pacifica%20serpentine%20belt/RallyVermont/engine2.jpg

Oct 01, 2009 | 2004 Chrysler Pacifica

Not finding what you are looking for?
2004 Chrysler Pacifica Logo

Related Topics:

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...