Question about 2002 Daewoo Nubira

1 Answer

Timing belt broke how do i set marks where 2002 daewoo nubria

Please

Posted by on

  • 2 more comments 
  • Raymond Hall
    Raymond Hall May 11, 2010

    Is your vehicle a 8 valve or 16 valve?

  • yadayada
    yadayada May 11, 2010

    Required tools:

    13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers

    If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.

    Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.



    To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.

    In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.

    One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

  • yadayada
    yadayada May 11, 2010

    if the belt broke the engine has bent valves, u will need to pull the cylinder head and repalce them.

  • Cecil Winfield Nov 28, 2013

    An 16 valve

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

timing belt broke how do i set marks where 2002 da - f994ef8.png

This is for the 16v engine ,hope this helps

Posted on Jan 24, 2009

1 Suggested Answer

  • 176 Answers

SOURCE: how do I set the timing on a 2002 Daewoo nubria?

make sure you align all the marks on the gears that the timing belt runs on.

Posted on Jul 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace a serpentine belt on 2002 daewoo nubria


You will have to release the idler wheel. It is the only pulley wheel that that does not have a component on it. There is a bolt on that which you can loosen the whole belt with to replace it. A crow bar is usually used to adjust the tension back once you replace it.

Aug 30, 2014 | Cars & Trucks

1 Answer

Daewoo nubira 2002


Please follow this link to the see the whole process with diagrams of the belt change. Please note if the belt broke you likely have bent valves.

Oct 17, 2012 | 1999 Daewoo Nubira

1 Answer

Proceedure for replacing timing belt on an 04 Chevrolet Optra LS


If this belt broke you have bent engine valves, di it break? Is this the DOHC engine like the one used in the Daewoo Nubria? If so read on.
Please access this link, I think it is the same exact engine. If not you can access the info for a fee here

Jul 15, 2012 | Chevrolet Optra Cars & Trucks

2 Answers

Need timeing belt diagram for 2000 dawoo nubria how to instill


CLICK HERE and HERE for timing belt information on the Nubria

blueextc3221_1.gif

Thanks for using FixYa

Aug 03, 2011 | 2000 Daewoo Nubira

1 Answer

How do I set the timing on a 2002 Daewoo nubria?


make sure you align all the marks on the gears that the timing belt runs on.

Jul 11, 2010 | 2002 Daewoo Nubira

1 Answer

TIMING MARKS FOR TIMING BELT ON A 2001 DAEWOO NUBRIA


CLICK on the following LINK. It has the Timing Belt and Mark Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2001/make/daewoo/model/nubira/2001_daewoo_nubira_timing_belt_diagram_marks.htm

Mar 10, 2010 | 2001 Daewoo Nubira

2 Answers

The timing belt broke, need to know what are the points?


THIS IS YOUR TIMING BELT DIAGRAM .CAMSHAFT AND CRANK PICTURE .

4180ab7.jpg

33d6a22.jpg

Jan 17, 2009 | 2002 Daewoo Nubira

1 Answer

Timing belt broke


Daewoo engines bend valves when the belt fails ,confirm this with a cylinder leakage test.
Here is a picture of the timing for a 16 valve engine
11fa785.png

Dec 27, 2008 | 2002 Daewoo Nubira

Not finding what you are looking for?
2002 Daewoo Nubira Logo

1,654 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...