Question about 2002 Daewoo Nubira

1 Answer

Timing belt broke

How do i set the timing marks

Posted by on

  • 4 more comments 
  • culpfontana5 Dec 27, 2008

    vavles are not bent

  • culpfontana5 Dec 28, 2008

    car cracks over but does not start

  • Anonymous Feb 01, 2009

    Fit cam belt

    Nubira 1998 16V - it is easy to find the timing marks on the cover. On the cam pulleys are a lot of mark ie exhaust, intake, etc. Which marks must line up with marks on cover? The TDC mark on crank pulley is also easy to find.

  • yadayada
    yadayada May 11, 2010

    the fact it cranks does not mean the valves are not bent, if this engine breaks a belt it bends or breaks the intake valves.

  • yadayada
    yadayada May 11, 2010

    How do u know this?

  • yadayada
    yadayada May 11, 2010

    If the belt broke the valves are bent, u will need to pull the cylinder head off and have them replaced and a valve job done.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Daewoo engines bend valves when the belt fails ,confirm this with a cylinder leakage test.
Here is a picture of the timing for a 16 valve engine
timing belt broke - 11fa785.png

Posted on Jan 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can someone please provide me the timing diagram or tell me how to reset the timing after the belt breaks or where the timing marks location is


Markings are usually on the Cam and Crank Sprokets. Not sure what car you are asking about but Most cars have interference engines which means If the Belt broke and wasn't being changed during regular maintenance then you probably bent some Valves in the Head. You have an expensive problem now

Mar 22, 2016 | Cars & Trucks

1 Answer

1991 Mazda Miata 1.6l timing belt broke.


You need to purchase a Haynes Manual or better. They are very common in your nearest chain part store. Like Autozone, Advance, Napa. More than likely you will have to set the crankshaft at TDC. "top dead center" and allign the two marks with the cam shaft! Watch when you put tension on the belt it will move the camshaft sprocket! And throw it back out of time.

Jul 13, 2012 | Cars & Trucks

1 Answer

How to install timing belt on 1993 toyota camry 4 cylinder


1993 Toyota 2.2 you have valve clearance,meaning if you broke the belt driving you just broke a belt and NO VALVE DAMAGE. On the cam gear line that dot on top with the mark at the top if the cylinder head it a little dipple.As for the crank just line up the dots.There is nothing confusing turn one at a time or both at a time.

Mar 09, 2012 | Cars & Trucks

2 Answers

Timming belt broke from water pump broke while driving car put new water pump on n timming belt but car doesnt start right plus shakes doesnt sound right 2001 neon dodge


Sounds like timing belt not on correctly. Check timing marks are aligned correctly when installing timing belt. This vehicle should have 2-3 marks to be aligned when installing belt.marks should be on cam gear/ crankshaft gear and intermediate shaft if engine is equipped with it.

Sep 10, 2011 | Dodge Neon Cars & Trucks

1 Answer

Timing belt broke on a 95 ford ranger.new belt


you have to line up the two marks on the gears and set the tension to the correct setting. then check the marks again. trial and error. i just did my timing belt on my ranger haha

Feb 18, 2010 | 1995 Ford Ranger Supercab

1 Answer

The timing belt on my 94 2.3L Ford Ranger broke, I have replaced but don't know how to set tming


The timiing is set by aliging the timing marks on the cam with the timing marks on the crank -- then the belt goes on.

Charlie

Aug 29, 2009 | 1994 Ford Ranger Supercab

1 Answer

Timing mark location and set up for t-belt, engine broke t-belt, just replaced head assy


TIMMING BELT MARKS
NEED MORE INFO ON ENGINE 4 CYL OR 6 CYL
ALSO IF YOU JUST REPLACED THE HEAD ASSEMBLY MEANS YOU BENT THE VALVES WHEN THE BELT BROKE. TIMMING MARKS ARE DIFFERANT ON MANY MAKES PURCHASE A CHILTON MANUAL FOR THE YEAR AND MAKE OF YOUR CAR THESE MANUALS ARE GREAT AND TAKE THE GUESS WORK OUT OF THE TIMMIMG MARK ISSUE

Aug 22, 2009 | 1998 Hyundai Elantra

1 Answer

My friend owns a 2003 cadillac cts 3.2 ltr engine. he needs to replace his timing belt because it broke but there are multiple timing marks on the harmonic balancer and 4 marks on the block, so he doesnt...


If the timing belt broke, he should take it to have it replaced because theres more than likely to be bent valves in the head. Heads should be checked before putting another timeing belt on. If there is valve damage, then more than likely there damage to the pistons too.

Dec 13, 2008 | 2003 Cadillac CTS

2 Answers

Timing


how do you set the timing belt

Aug 13, 2008 | 1988 Dodge Ram 50

Not finding what you are looking for?
2002 Daewoo Nubira Logo

Related Topics:

378 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...