Initinally when ignition is turned on the light on the D4 blinks with the check engine light then it goes off but won't even turn ...no sound from solinoid...nothing indicating low battery...battery is strong and fully charged...even tried jumping with another car ,still nothing happens....could this be a bad solenoid?
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
D4 is a transmission problem. It wouldn't cause the car not to start. If you don't hear the pump coming on when the key is turned on, Most likely the pump died. Could be the fuse or wiring also. Check grounds. Both could be a bad ground.
The D4 light is coming on to tell you that there is one or more fault codes set in your transmission control module. The only way to retrieve codes on the 1995 models is to read "Flash Codes" output by the D4 light. (See instructions below)
RETRIEVING FLASH CODES USING THE D4 LIGHT
If fault codes are present, the D4 light will "blink" when the ignition is turned to the RUN position and will remain on at all times when the engine is running.
To retrieve the flash codes, turn the ignition switch off.
Install a jumper wire between the service check connector terminals.
The service check connector is a gray, 2-pin connector located on the PCM/TCM cover under the passenger side of the instrument panel. (See picture below)
CAUTION: DO NOT use the 3-pin located next to the service check connector.
Installing the jumper will place the PCM/TCM in diagnostic test mode.
Turn the ignition to the RUN position. Codes will be output by blinking the D4 light.
Note the number of blinks from the D4 light. A short blink indicates a single digit flash code. A long blink equals 10 short blinks. For instance one short blink indicates code 1. One long blink and four short blinks indicates code 14. If there is more than one fault code, they will be output one at a time from the lowest numbered code to the highest numbered code. It is recommended that you read the code or codes several times to make sure that you are reading it correctly.
Once you have retrieved the fault code(s) re-post your question and include the information for what codes you have and someone can then help you locate the cause of the problem.
Hi, a few questions 1st. Did your mechanic check for engine codes? Is your Honda a v-6 or 4 cylinder? The flashing D4 light indicates a possible transmission malfunction. You should avoid rapid acceleration until the cause of the light blinking is determined. If you have the V-6, there is a diagnostic port to connect a scan tool to read any stored engine codes that have turned on the check engine light. This port is located behind the ashtray in the center console (most cars did not have this til 96). If you have the 4 cyl engine, there is a service connector located under the dash on the pass. side. Inside the connector is what looks like a 2 wire plug should be attached. Take a paper clip, unbend it, and insert the 2 ends of the clip into the connector to 'jump' it. Turn the ignition switch to the on position (don't start the vehicle), and the check engine light will flash. Count the flashes, short flashes are for code #'s 1 to 9 (single digit code), a 2 digit code will be a long flash for the 1st digit, followed by a short flash for the 2nd digit. If there is more than one code, they will be separated by a pause. They will repeat so you can count them and write them down. Let me know what the code #'s are so I can help further. Curt
Theres a transmission cooling sensor and somtimes the wire comes loose from other repairs being done around it. or its just out. its on the left side sitting on the tranny. THATS WHY your d4 light is blinking