Question about 2004 Toyota RAV4

1 Answer

Need transmitter programing guide for my 2004 tacoma prerunner

I have lost both my transmitters and the dealership want $100.00 to program a new one. I purchased a new transmitter and would like to program myself. Thanks

Posted by on

  • Anonymous Mar 15, 2014

    programming transmitter

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 21,949 Answers

Dealer only,encrypted software as its classed as security and the software dosent have to be shared or released ,pay the golden egg and smile .

Posted on Dec 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to program a new alarm remote


Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver's seat.
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation .



Hope this helps, I found it online

-Scott

Feb 19, 2015 | 2004 Pontiac Grand Prix

1 Answer

How can I program a key fob


GRAND PRIX KEY FOB PROGRAMMING INSTRUCTIONS Transmitter Programming No Tools Required In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver.Up to 4 transmitters may be programmed Important Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver

Apr 22, 2013 | 2001 Pontiac Grand Am SE

1 Answer

Hello, I have a question, how to do yo reprogram the remote control on a 2004 GMC Yukon?


CLOSE ALL DOORS INSERT KEY INTO IGNITION.DO NOT TURN THE IGNITION SWITCH.PRESS AND HOLD DOOR LOCK SWITCH IN THE UNLOCK POSITION.SWITCH THE IGNITION ON OFF ON OFF.RELEASE DOOR LOCK SWITCH.SYSTEM SHOULD NOW LOCK AND UNLOCK VECHICLE INDICATING PROGRAMMING MODE ACTIVATED.PROCEED AS FOLLOWS.NOTE EXISTING REMOTE TRANSMITTER MEMORY POSITIONS WILL BE OVERWRITTEN.PRESS AND HOLD LOCK AND UNLOCK BUTTONS ON THE FIRST REMOTE TRANSMITTER FOR 15 SECONDS.SYSTEM WILL LOCK AND UNLOCK VECHICLE INDICATING REMOTE TRANSMITTER PROGRAMMED.REPEAT ABOVE PROCEDURE FOR EACH REMOTE TRANSMITTER.IF THIS DONT HELP DEALERSHIP HAS TO REPROGRAM REMOTE.

Aug 09, 2010 | 2004 GMC Yukon

1 Answer

How do i program a 2004 malibu keyless remote


The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly.

The scan tool must stay connected until all of the transmitters are programmed.
  1. Install a scan tool.
  2. Turn ON the ignition with the engine OFF.
  3. With the scan tool, select Body,go to Remote Function Actuation.
  4. Select Special Functions.
  5. Select Program Key Fobs.
  6. Select the number of key fobs to be programmed.
  7. Press and hold the LOCK and the UNLOCK buttons simultaneously on the first transmitter for approximately 15 seconds . The Power Locks should cycle to confirm programming of the first fob is complete.
  8. If you are programming more than one transmitter, repeat the previous step to program up to four transmitters.
  9. Remove the scan tool.
  10. Exit the vehicle. Attempt to lock/unlock the doors to verify the programming.
  11. Operate the transmitter functions in order to verify correct system operation.

May 27, 2010 | 2004 Chevrolet Malibu Maxx

1 Answer

I just bought a remote and I need to program it in an 06 chevy equinox. How do I do it?


Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly.

  1. Install a scan tool.
  2. Turn ON the ignition with the engine OFF.
  3. Select Body Control Module.
  4. Select Special Functions.
  5. Select Program Key Fobs.
  6. If you are adding a transmitter to the system, or are replacing a transmitter, choose the Add/Replace Key Fobs option. This allows new transmitters to be added without deleting those currently programmed to the module. If you are replacing all transmitters or none of the transmitters are working, choose the Clear memory and Program All Fobs option. This prevents lost or stolen transmitters from being used to access the vehicle.
  7. Follow the scan tool on-screen directions.
  8. After programming the last transmitter, remove the scan tool.
  9. Exit the vehicle. Attempt to lock/unlock the doors to verify the programming.
  10. Operate the transmitter functions in order to verify correct system operation.
  11. if you don't have a scan tool then you can go to a lock smith they can do it cheaper than the dealer sometime.

May 25, 2010 | 2006 Chevrolet Equinox

1 Answer

How can i program my new keyless entry fob for my Isuzu Ascender


If it is a new key fob it will have to be programmed by the dealer.
This is the statement as listed in the owners manual for your vehicle.

Matching Transmitter(s) to Your Vehicle
Each remote keyless entry transmitter is coded
to prevent another transmitter from unlocking
your vehicle. If a transmitter is lost or stolen, a
replacement can be purchased through your dealer.
Remember to bring any remaining transmitters with
you when you go to your dealer. When the dealer
matches the replacement transmitter to your
vehicle, any remaining transmitters must also be
matched. Once your dealer has coded the new
transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have a maximum of four
transmitters matched to it.
94

Oct 02, 2009 | 2007 Isuzu Ascender 7 Passenger

1 Answer

THE REMOTE DOOR LOCK ON A 2000 BUICK CENTURY HAS QUITE WORKING. THE FOBS ARE GOOD BUT WON'T OPEN ANYTHING.


The transmitter may have lost programming,
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.

IMPORTANT:

  • Once entering this procedure, programming the first transmitter erases all previous transmitters. You must program all transmitters.
  • Program one vehicle at a time. One transmitter could be programmed into other vehicles that are also on program mode in close proximity.
  1. Sit in the driver's seat.
  2. Remove the ignition key from the ignition lock cylinder.
  3. Close all vehicle doors.
  4. Press and hold unlock on the door lock switch.
  5. While holding the door lock switch in the unlock position, insert and remove the ignition key twice. Do not rotate the ignition lock cylinder.
  6. Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must remain in the LOCK position for the rest of the procedure.
  7. Release the door lock switch. You will hear three chimes. This chime feedback indicates that transmitter programming is active.
  8. Press and hold the lock and unlock buttons at the same time on the keyless entry transmitter for 12 seconds . You will hear two chimes. This chime feedback indicates that the transmitter has been programmed successfully.
  9. Repeat step 8 for the rest of the transmitters (for a total of 4 transmitters).
  10. Exit this procedure by removing the ignition key from the ignition lock cylinder.

May 07, 2009 | 2000 Buick Century

2 Answers

I have a spare keyless entry remote for my 2005 Mercury Mariner. How can I program it?


sorry,but the only way is dealership.shouldn't cost much if anything.

Mar 28, 2009 | 2005 Mercury Mariner

1 Answer

Programming keyless remote for Neon 2004


There is a way to program a remote if there is already a valid remote. Unfortunatly if you don't have a valid remote the only way to get one programmed is at the dealership with their scan tool.

I have pasted directions for programming a remote if there is already a valid transmiter.


CUSTOMER PROGRAMMING For a customer to be able to program RKE transmitters themselves, at least one RKE transmitter must be programmed already. This procedure is to add additional transmitters. If all transmitters are lost, the DRB III® scan tool must be used to program the new transmitters.
  1. Insert the key into the ignition switch, and turn the ignition switch to the RUN position without starting the vehicle (allow chimes to stop).
  2. Using the RKE transmitter programmed to the RKE module, press and continuously hold down the UNLOCK button for 4-10 seconds.
  3. Within the 4-10 second time range, continue to hold the UNLOCK button and press the PANIC button. Both buttons may then be released. Upon the PANIC button being depressed, the message for customer programming mode will be transmitted to the RKE module.
  4. A chime will be heard to verify that the customer programming mode has been entered (allow 3 seconds to hear chimes).
  5. Press and release any button on each transmitter that is to be programmed to the RKE module, including any transmitters which were previously programmed to the RKE module (with a maximum of four possible). After each transmitter is successfully programmed, a chime will be heard to verify that successful programming of the transmitter has occurred.
  6. After thirty seconds, or upon the ignition switch being turned OFF, the RKE module will exit programming mode.

Jul 30, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
2004 Toyota RAV4 Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...