Question about 1985 Chevrolet S-10 Blazer

1 Answer

1999 s-10 blazer 4x4 no worky when button is puhed, but lights up

I have a 1999 s-10 blazer when i push the 4x4 button it lights up but will not engage in any position but 2 wheel drive

Posted by on

  • Anonymous Jan 04, 2009

    actuater is fine on my blazer 4x4 no vac leaks. tried pulling cable only pulls a little bit.here clicking when switching to 2wd or 4wd but does not engage.plz help solve problem for my 1999 blazer 4x4 3 switch

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Change the vacuum actuator it is located under the battery

Posted on Dec 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 93 chevy s10 4x4 blazer, my instrument panel worked before new motor was put in, after having the new engine put in, my fuel gauge, oil pressure, voltmeter, rpm, and my temp gauge all quit worki


Look for a missing ground strap from the engine to the body or frame. Remember the engine sits on rubber mounts so that ground strap is essential.

Feb 21, 2014 | Cars & Trucks

1 Answer

99chevy blazer when i push the button to use the 4x4 the lights just flash wat does this mean


Will it go into 4x4 at all, high or low? I had this same issue where the it wouldn't go into 4x4 at all and had to replace the transfer case.

Nov 27, 2010 | 1999 Chevrolet Blazer

1 Answer

My 99 blazer is push button 4x4 the lights on the 4 low 4high and 2 high quit working don't have 4 wheel drive anymore have roaring sound coming from front in when going any rate of speed.


I have seen the switch in the dash go bad and also the 4x4 module in the passenger side kick panel will collect moisture you can look at the plug in of the harness for green corossion.

Oct 14, 2010 | 1999 Chevrolet Blazer

2 Answers

I have a 1997 4x4 Blazer that wont go into 4x4.


just had simular prob.. check front diff for fluids, check actuator, and also there is a switch on the top of your transfer case . all else fails, have vehi. on jack stands (all 4 tires off the ground) start, hold brake, push button,and have someone under to watch cable ect. (""do not put in gear or give gas while doing this"")

Dec 25, 2008 | 1997 Chevrolet Blazer

3 Answers

Transfer case motor for push button 4x4


i have a 1993 blazer 4.3 w code 4x4 with a 4L60 E . my truck wouldn;t go in 4 hi or low. so i changed the transfer case motor and it works fine now. If you turn the ignition key to on but not crank the engine and open the driver door and push 4 hi button, you should hear the transfer case motor cycle for 3 or 4 seconds every time you push button and the light will flash until it goes in 4wd If the 4 hi button light doesn't flash during cycle then it could be a bad switch. if the transfer case motor won't cycle it could be a fuse or a bad transfer case motor . Hope this answers your question.
pgale89

Dec 16, 2008 | 1994 Chevrolet S-10 Blazer

1 Answer

1994 chevy s10 blazer 4x4 push button type


small sylinoid on the top of the transfer case needs replaced. easy to do. it has three vacumelines going to it just trun out and replace like a bolt.

Dec 10, 2008 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...