Question about 2008 Hyundai Accent

3 Answers

I want to get rid of the stupid door chime.

I know for most Ford vehicles, you can hit the buttons in a certain order to make the seat belt chime stop aggravating the **** out of you. I was wondering if there was one for a 2008 Hyundai Accent for the door and seat belt chime.

Help is greatly appreciated!

Posted by on

  • silver top May 11, 2010

    hi from uk please bear with me on this?? but the chime you mention should only sound if door is opened whilst side/tail lights are still on ? also if you have unwittingly left the switch for rear fog light in the on position ? chime will also chime and i assume you know that if this switch is on? the rear fog only lights when headlights are selected this is the normal operation on hyundais here in uk may i suggest you recheck switches to ensure they are in off position the chime is just a warning that a light switch is in on position but not necessarily lighting a lamp ? this chime is not connected to the seat belts as far as i know but there is a light comes on in red on the dash display if drivers seat belt is not used/connected into its lock ? hope this helps best wishes from n/west of uk

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

That door chime was driving me crazy too. It turned out to be really easy to pull the power cord from the chime. If you fold down the glove box by pulling the two plugs out from the inside, you can see the chime up behind the dash just to the left of the glove box. Just pull out the cord attached by removing the clip and you are golden.

Ahhhh. Sweet relief. I have been chime free in my accent for 2 months, and it makes for a much more enjoyable car.

Enjoy!

Posted on Jan 13, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

There is a pin on the inside of the driver's side door - covered with a black piece of rubber - We built up a layer of 2 to 4 pieces of duct tape on the swinging door to hold the pin tigher - every now and then you need to replace the duct tape -and just to everyone else - it was ringing with the seat belt on while driving sometimes - for hours!! I took it to the dealer and they had only a temporary solution - the bell will still ring when you leave the keys in the car by accident and if you don't put your seat belt on! Marsha

Posted on Aug 28, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How about a: wear your seatbelt, moron and b: close the door!

Posted on Feb 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i disconnect fuse to seat belt alarm tried three time method didnt work


The seat belt warning chime is controlled by the central timer module ! You can't just disconnect fuses , other things may stop working !
Safety Belt Warning Indicator Lamp and Chime
The safety belt indicator and chime feature is controlled by the CTM. The driver safety belt switch is hardwired to the CTM. If at any time during the first 60 seconds after the ignition switch is placed in position II, if the driver safety belt is sensed as being unfastened, the CTM will process the input, and in turn, output a signal to the CTM through a hardwired circuit. In turn the CTM will output a visual warning to the instrument cluster. If at any time during the first six seconds after the ignition switch is place in position II and the safety belt is not fastened, the safety belt warning chime will sound.
When the seat belt is connected the warning still chimes ? Could have code stored in the CTM .
B1464 Safety belt switch circuit short to battery CTM Go To Pinpoint Test B .
SoW

Jun 30, 2015 | 2002 Ford SVT Focus

2 Answers

How do I disable the seat belt alarm


Why would you want to disable it?

Feb 22, 2015 | Seat Cars & Trucks

5 Answers

How do i turn off the annoying seat belt chime?


It is chiming with the seat belt in operation then have it checked out. I you do not wish to wear the seat belt just do it up and sit on it Why anybody would want to turn of a safety alarm is a bit beyond comprehension.

Aug 16, 2014 | 2000 Pontiac Grand Am GT

2 Answers

Is there a passcode or sequence to disable the


As far as I know that seat belt warning chime and light is there for your safety and protection, it should not be bypassed in any way.
There is no by pass seqwuence or code to eliminate this safety device.
Buckle up, its the law.

May 09, 2010 | 2002 Ford Mustang

1 Answer

Warning bell won't stop sounding


Section 13-09: Gauges, Warning Devices — Chime System 1996 Windstar Workshop Manual
DESCRIPTION AND OPERATION Warning Chime Systems Three distinct sounds are used to indicate the area of concern. Seat belt warning generates 1 chime per second
key-in-ignition generates 2 chimes per second
headlight on generates 4 chimes per second.
Key-In-Ignition Warning The key-in-ignition warning will sound when the driver's front door (20125) is opened with the key in the ignition switch. It will continue to sound until the key is removed, the front door is closed, the ignition switch is turned to START or the vehicle speed is over 24 kmh (15 mph).

Safety Belt Warning When the ignition switch is turned to RUN or START from OFF or ACC, the chime will sound for six seconds or until the safety belt is buckled.
  • The safety belt warning indicator lamp (10C859) will activate for 60 seconds or until the driver's safety belt is fastened. Both the chime and lamp activate at the same time.
Anytime the ignition switch is released from START and returns to RUN while the safety belt lamp or chime is activated, the safety belt warning lamp or chime will remain activated until either the timing sequence has been executed, or the safety belt is buckled.

Headlamp Switch On Warning The chime will be activated if the headlamps or parking lamps are ON, the key is not in the ignition and the driver's door is opened. The chime will sound at a rate of four per second.

Apr 23, 2009 | 1996 Ford Windstar

1 Answer

Can't get the bell to stop dinging


Check your fuses. It's wierd but there is a certain fuse that blows and the chime is non stop!!

Apr 12, 2009 | 1988 Volvo 240

1 Answer

The seat belt chime stays on even though the seat belt is engaged


Someone has kicked the little connector under the seat loose. Check under there with a flashlight, and reseat any connectors found.

Mar 16, 2009 | 2003 Ford Focus

2 Answers

1995 Jeep Grand Cherokee seat belt noise and light.


Hi
There is a switch in the seat belt latch whe your sitting in the seat this will ba the part o the right side, see if something went into the latch part? or the switch is bad i think you have to replace the belt to fix the switch
RD

Jan 19, 2009 | 1995 Jeep Grand Cherokee

2 Answers

Arter I put on Seat Belt, another chime goes on for 6 rings,then stops


HI.
ON Ford cars and Suv's,
Some times the sound chime after the seat belt buklet.
Is like a open door.
The problem on this car is that the the DOOR AJAR SWITCH. come danaged. and the Body cumputer don't recievethe door close signal.
But is intermitent.
The door ajar switch is on the door lacth.
You only can get front the dealer.
OK. I hope this information can be useful for you.

Thank you.

Jul 17, 2008 | 2001 Ford Explorer Sport

Not finding what you are looking for?
Cars & Trucks Logo

1,057 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...