Question about 1999 Jeep Grand Cherokee

1 Answer

Repair rear end

How to replace a rear end.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 962 Answers

You have to remove the entire axle assembly as a whole . That is if your's is not fixable. Replace with the same model size ,size etc. So no alignment problems will occur.

Posted on Dec 27, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front right wheel alignment


Have a front end safety check done first and repair / replace faulty units . Have a wheel alignment done but have them check the rear end alignment first as it affects the front settings. Worn bushes in the suspension arms allow the rear end to run side ways to the front.

Dec 20, 2013 | 1995 Chevrolet Caprice Classic

1 Answer

Noise from rear-end on jeep chrokee


Hey Dennis,
Have you checked the lube level in the read differential? If its good, you have a wheel bearing going bad. To replace it, you will need to remove the axle.. This is not a hard fix, but you have to have the ALL the tools and you MUST put the rear end up on jack stands..DO NOT use a jack to hold the rear end up.. IF you are not very mechanically inclined, please take this to a qualified professional..
Auto Truck Repair Manuals by Chilton Haynes Clymer Factory
Jeep Cherokee 1984 2001 Repair Manuals
http://repair.chiltondiy.com/Pub/DIY/Product/1998-Jeep-Cherokee-repair-manual-online?ca=Repair&b=2229

Jun 27, 2017 | 1998 Jeep Grand Cherokee

1 Answer

99 jeep cherokee drive line sheered at rear end


well first of all take it easy on the burnouts! ha ha. if you sheared the yoke thats a simple fix, youll just have to replace the pinion seal and the nut might be jammed on there pretty good so your going to need an impact wrench and of course a new yoke. and i would have the driveline checked before re-installing, just because it didnt break doesnt mean its not torqued. once you replace the yoke and pinon seal install the drivline and youre good to go. however if you torqued the pinion gear any its game over bro, and repairing the rear end is going to be beyond your skills. (in order to re set, shim and square the rear end you need to be a skilled mechanic, no guess work, no doing it out of a repair manual) hope this helps, good luck

Mar 08, 2012 | 1999 Jeep Grand Cherokee

1 Answer

How to repair a 3 inch crack in the rear bumper of a 2002 buick century. Damage was caused by a rear end accident.


Those are esier to replace the entire bumper than repair, Ebay sells new shells for 165.00

Jun 09, 2010 | 2002 Buick Century

2 Answers

Truck has a humming noise from the rear end which


Sounds like the rear end itself, most likely if u have high mileage.

May 22, 2010 | 1988 Jeep Cherokee

1 Answer

The rear end is going out,whats the easiest way to repair it?


If you have limited mechanical skills the easiest way to fix it is to find a good one in the junkyard and replace the whole rear axle. if you do your own brake jobs then you could probably do that. Otherwise you will need to take it to a shop to have the gears/bearings replaced and the rear end reset up.
Of course it all depends on what part of the rear end is going bad. Most shops will do a complete rebuild so your rear end will be like new. While some people will just replace the one item that has gone bad.
Usually when something goes bad in the rear end it contaminates and causes some collateral damage to the rest of it so a complete rebuild is recommended.

Apr 08, 2010 | 1993 Land Rover Range Rover County

2 Answers

Vaccum line fell off rear end not sure where it belongs


the vent tube for the ring and pinion housing is the only tubing made of rubber for the axle

Feb 14, 2010 | 1997 Dodge Ram 2500 Club Cab

1 Answer

Need a diagram or information on how to replace Rear end....Making loud scrubbing noises and will not shift into reverse now!


try this website its Dodge repair information www.alldatadiy and maybe you be able to get the diagrams you need Michigan Man.

May 08, 2009 | 2000 Dodge Ram 1500 Truck

2 Answers

Rear disc brake line


Flex line screws into the block where the two steel lines for each side brakes are joined.

Apr 08, 2009 | 2000 Ford F150 Flareside SuperCab

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...