Question about 2006 Hyundai Accent

Open Question

Hyundai Accent Cranhshaft pulley removal

How do I lock the crankshaft of a Hyundai Accent in order to remove the Cranhshaft pulley?

Posted by on

  • insinor8 Mar 23, 2009

    I'm working on a 1995 Hyundai Accent...needed to pull everything off to find where the a coolant leak we originating from and now I need to get the Crankshaft pully off!! I don't see anywhere to stick a tool to "lock" it into place. Any suggestions? It's my girlfriends car....not a terrible car with 181K miles....just finding a lot of things that were "fixed" on the car at one point or another after changing the radiator for her....was considering pulling everything out from under the hood (as a joke) just to double check things. Thanks for the help!

  • GoneToPlaid May 11, 2010

    Is there not any hole (or cover plate) at the rear of the engine where the flywheel is located? My old Mazda had a hole where I was able to wedge in a large screwdriver against the flywheel teeth, allowing me to loosen the crankshaft pulley bolt. Have you tried talking to a Hyundai mechanic and asking him what the trick is?

×

6 Suggested Answers

MrScary66613
  • 1990 Answers

SOURCE: need to remove window crank 2004 hyundai accent

Your Local Auto Parts Store has the Tool that you need for this Removal. Some of them will let you Rent it instaed of paying the 50.00 Bucks for the Tool.

Posted on Jan 24, 2009

DJ_Doc
  • 3 Answers

SOURCE: hyundai accent '02 inside door handle & Lock removal

Removing the door is very tricky, trust me on this. I ended up breaking it the first time, so please learn from my mistake.

1. Remove all visible screws: 2 at bottom of door, 3 on front near hinge, 1 on inside the door lever. You will need an average size phillips screwdriver to do this.

2. On the door handle itself, you will see two circles. Pop the front one out. You will need a LARGE size phillips screwdriver to do this.

3. Once screws are removed, take a (standard) flat-head screwdriver, preferable one with a large face, and pry the triangular piece of plastic (that covers the outside SIDE mirror) off. This will aide in puting the door panel back on...TRUST ME!!!

4. Take the same flat-head screwdriver, and pry behind the door lock (at the same time, push forward toward the door hinge). The assembly should pop out.

5. Gently pry the door panel from the door, making sure not to break any unnecessary pieces along the way. The door panel should be hanging by the window sill opening.

6. This is where it will get tricky. It is advised that you use help with this part: Angle the door panel at a 45 degree angle. AT THE SAME TIME, slightly bend and twist the door lock handle until it fits through the hole. You will see the 3 pegs the held it in the door from before. Also note: Be careful not to break the 2 poles that are attached to the lock.

7. After popping the lock through the hole, you should be able to lift the door upward, and off the sill. Repeat these steps in reverse order to re-attach door panel.

Be careful not to rip sound-deadening paper found on inside of door unless you intend to remove or replace it! Not only does it prevent dirt and moisture from entering your door (and possible rusting it from the inside out), but it makes your speakers sound better too!

-SportTunerFreak

**It is also recommended to put a tiny bead of silicone on the inside of the door panel to help suppress any rattling, and prevent moisture and dust from entering. It also helps your screws obtain a tighter fit. Hope this helps!

Posted on Mar 24, 2009

  • 1 Answer

SOURCE: how do you remove radio from hyundai accent 1998

You have to take out the ash tray, and remove those two screws, then pop out the center dash trim. Careful, though, you have to take out a lot of the wiring inside of your center dash trim in order to pull it out for enough room to move the radio in and out. I'm doing this right now, actually..

Posted on May 22, 2009

  • 523 Answers

SOURCE: Crankshaft Woodruff Key Removal

You are correct, this key does drive both. While I have never tried to remove the keway with out both pulley and lower sprocket you may be able to (my gut says no but anything is worth trying once) I'd position the keyway at the 12 o'clock postion and with a good pair of needle nose pliers see if the key will roll out as you pull up and away with it. If it will not you'll of course have to remove the front of the engine and pull the timing belt, if over 60K miles on belt go ahead and replace with new.

I hope this may have assited and good luck!

Tom

Posted on Apr 09, 2010

ftw1952
  • 10319 Answers

SOURCE: I can't get the crankshaft damper pulley off.

Download this link and find your Service manual for your vehicle. It will serve you well and to keep for future reference

http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 02, 2010

  • 5 Answers

SOURCE: 2001 PT Cruiser: How too remove crankshaft pulley 2001 PT Cruiser...

GET A 3 SPOKE PULLEY EXTRACTOR AND SCREW IN THE BOLT BUT IN THE CRANKSHAFT HOLE PUT A MUCH SMALLER SCEW SO YOU WOUNT MESS THE INSIDE UP

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the crankshaft dumper pully?


Published: 11-May-2011
Engine - V8 4.4L Petrol - Crankshaft Pulley
In-vehicle Repair
Special Tool(s)

Holding Tool Crankshaft Pulley
303-893(LRT-12-080)
Adapter
303-191-03
Bolts and spacers
303-191-04
Remover, crankshaft pulley
303-588
Remover, crankshaft seal
303-D121
Installer, crankshaft seal
303-1100
Adapter - Crankshaft seal installer
303-1100-01 Removal
  1. Disconnect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).
  1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle.
  1. Remove the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).

  1. Remove the cooling fan shroud.
    • Release 2 clips from the cooling fan lower shroud.
    • Release and remove the cooling fan lower shroud from the cooling pack.

  1. Using the special tools, retain the crankshaft pulley.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. NOTE: The crankshaft pulley retaining bolt will be very tight.
    Remove the crankshaft pulley retaining bolt.
    • Discard the bolt.
  1. Remove the special tools.

  1. Using the special tools, remove the crankshaft pulley.
    • Collect the locking ring.
  1. Remove the special tools from the crankshaft pulley.

  1. Using the special tool, remove the crankshaft front seal.
    • Remove the outer section of the seal.
    • Repeat the process to remove the inner section of seal.
  1. Check the crankshaft damper pulley and locking ring for damage.
Installation
  1. Clean all the crankshaft pulley mating faces.

  1. Using the special tools, install the crankshaft front seal.
    • Lubricate the seal with clean engine oil.
    • Use the discarded crankshaft bolt with the service tool.
  1. Install the crankshaft pulley.
    • Lubricate the seal with clean engine oil.
  1. Install the crankshaft pulley locking ring.
  1. CAUTION: The screw thread in the crankshaft pulley must be cleaned out before installing a new crankshaft pulley bolt. Install, but do not tighten, the new crankshaft pulley bolt.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. Using the special tools, retain the crankshaft pulley.
    • Tighten the crankshaft pulley bolt to 380 Nm (280 lb.ft).
  1. Remove the special tools.
  1. Install the cooling fan lower shroud.
  1. Install the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).
  1. Connect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).

Jan 27, 2016 | 2006 Land Rover Range Rover Sport

1 Answer

Where is the cam sensor 2002 hyundia accent 1.5?


    More images for Where is the cam sensor 2002 hyundai accent 1.5

    Hyundai Crankshaft Position Sensor Removal - YouTube

    ? 3:42
    https://www.youtube.com/watch?v=0YLYDU_5w8w
    Jul 12, 2012 - Uploaded by richpin06a
    Hyundai Elantra Crankshaft Position Sensor Removal.

    Hyundai accent 2001 - YouTube

    ? 2:44
    https://www.youtube.com/watch?v=fzqMNho3xIU
    Nov 25, 2012 - Uploaded by mig dups
    2000 Hyundai Accent GS turns over - no start. ... HyundaiCrankshaft Position Sensor Replace Timing Belt ...


Dec 26, 2015 | Cars & Trucks

1 Answer

Accent broking timing belt now misfire 1&4


Lift the vehicle by using of jack.
Remove the engine support bracket.
Remove the power steering belt.Remove the air conditioning compressor belt.Remove the alternator belt
Remove the coolant pump pulley.
Remove the crankshaft pulley.
Remove the timing belt cover.
Move the timing belt tensioner pulley toward the coolant pump and temporarily secure it
.Remove the timing belt
Remove the camshaft from the camshaft sprocket
Remove the crankshaft sprocket and flange.
Remove the timing belt idler.
Remove the timing belt tensioner.

re install in reverse order. chances are the rod is bent but without breaking down the cylinder the only way to determine is to but a new belt on and see what happens. good luck.

Mar 11, 2013 | 2001 Hyundai Accent

1 Answer

How do I change the Serpentine belt on my 2001 Hyundai Accent?


Thank you for the inquiry.
Let's try this procedure:
1) Raise and support the front of the car on jack stands. Remove the passenger-side tire/wheel assembly, using a lug wrench. Remove the inner splash shield to gain access to the crankshaft pulley, using a 10-mm socket. Remove the accessory belts by loosening the tensioner with a wrench.
2) Remove the water pump pulley, using a socket. Remove the crankshaft pulley bolt, using a ½-inch drive socket followed by the pulley. Remove the upper and lower timing belt covers, using a 10-mm socket.
3) Insert the crankshaft pulley bolt back into the nose of the crankshaft so the engine can be turned. Turn the engine clockwise until the timing mark on the crankshaft sprocket and block are aligned and the camshaft sprocket hole and mark on the camshaft-bearing cap are aligned. There is a dot on the crankshaft sprocket and a corresponding dot on the block at the one o'clock position. There is a hole in the camshaft sprocket, which is at the 12 o'clock position. A dot can be seen through the hole in the camshaft sprocket when it is vertical and lined up perfectly.
4) Loosen the two bolts in the timing belt tensioner and pry the tensioner away from the timing belt, using a screwdriver. While holding the tensioner away from the belt, loosely tighten the two bolts to hold the tensioner in its current position. Remove the timing belt.
5) Install the new timing belt, starting on the right side opposite the tensioner. Start at the crank and work up and over the camshaft sprocket, keeping tension on the right side or opposite the tensioner. Loosen the bolts on the tensioner and allow the tensioner to apply pressure to the belt.
6) Rotate the engine two times clockwise and re-align the timing marks. If the marks align perfectly, tighten the two bolts in the belt tensioner. If they do not align, turn the crank or cam sprocket to align and re-install the belt. Replace the remainder of the parts in reverse order of removal.
I hope we've provided you useful assistance and that this information allows you to proceed from here. Please be sure to vote on my response.
I hope I've earned a good rating from you today.
Please post a comment if you need additional assistance so that I can help you further.
Best regards,
TF

Jun 03, 2011 | 2001 Hyundai Accent

2 Answers

I need 2004 Hyundai XG350L Service/repair Manual


3.5L Engine

Remove or disconnect the following:
  1. Negative battery cable
  • Engine coolant
  • Water pump pulley bolts
  • Alternator bolt, loosen only
  • Water pump pulley and drive belts
  • Crankshaft pulley
  • Timing belt cover(s)
  1. Turn the crankshaft until the timing marks on the camshaft sprocket and cylinder head are aligned.
  2. Loosen the timing belt tensioner bolt and turn the tensioner counterclockwise as far as it will go. Tighten the adjusting bolt.
  3. Mark the timing belt with an arrow showing direction of rotation.
  4. Remove the timing belt.
  5. If defective, remove the timing belt tensioner.

9767b45.gif
Timing belt sprocket alignment mark positioning for belt removal and installation—3.5L engine

To install:
  1. If necessary, install the timing belt tensioner.
  2. Attach the top of the tensioner spring on the engine coolant pump pin. Ensure the hook on the pin is facing down and the hook on the tensioner is facing away from the engine
  3. Rotate the timing belt tensioner to the extreme counterclockwise position. Temporarily lock the tensioner in place.
  4. Align the timing marks of the camshaft and crankshaft sprockets.
  5. Install the timing belt on the crankshaft sprocket, then onto the rear camshaft sprocket.
  6. Route the belt to the coolant pump pulley, the front camshaft sprocket and the timing belt tensioner.
  7. Apply force counterclockwise to the rear camshaft sprocket with tension on the tight side of the belt and check that timing marks are aligned.
  8. Loosen the tensioner bolt 1–2 turns and tighten the timing belt to a tension of 57–84 lbs. (260–380 N).
  9. Turn the crankshaft two turns clockwise.
  10. Readjust the sprocket timing marks and tighten the tensioner bolts.
  11. Install the timing belt covers.
  12. Install the crankshaft pulley and tighten to 108–116 ft. lbs. (150–160 Nm).
  13. Install or connect the following:
    • Timing belt cover(s)
    • Crankshaft pulley
    • A/C compressor belt
    • Water pump pulley
    • V belt
    • Negative battery cable
    • Engine with coolant

Feb 10, 2010 | 2004 Hyundai XG350

2 Answers

Removing inside door handle


The control panels are often held in place by either spring tensioners or some built into the plastic frame of the panel and can be pried up and out. They pretty much depend on gravity to keep it in place.
Once free of the panel, turning it may allow it to be passed through the hole in which it normally resides.
I would try first to pry with an old credit or bank card before resorting to metal tools.

Dec 12, 2009 | 2003 Hyundai Accent

2 Answers

Replacing exterior door handle 2003 hyundai accent?


remove door panel which is attached by screws,peel away plastic liner and look inside door at back of door handle..using needle nose pliers pop off the small steel rods that are for inside door mechanism,then remove the one bolt that attaches the handle to the inside of door and from outside of door remove handle.Replace in reverse order!

May 29, 2009 | Hyundai Motor 1995 Accent

1 Answer

How do i undo the nut on crankshaft pulley.


you will have to use a fly wheel locking tool or i usually just use a large flat tip screw driver and hold the fly wheel from turning while a friend loosens the nut on the pulley.

Mar 30, 2009 | 1999 Hyundai Accent

1 Answer

How to remove crankshaft pulley for 1999 hyundai. I only see one nut.


you need to take that nut or bolt our with the impact air tool
a electric may work but air tool has more power
then it might just slide out by hand but if not sometimes there is like tree little wholes on the pulley and the have thread to install a puller and remoove it

Jun 01, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
2006 Hyundai Accent Logo

Related Topics:

454 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...