Question about 1999 Chrysler Town & Country

1 Answer

Brake pedal goes to the floor and won't pump up. The van will stop but has a very soft pedal. I'm thinking master cylinder, would you agree?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 541 Answers

Sounds like it to me. Obviously it should remain parked until fixed.

Posted on Dec 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No brake pedal. pads good, fluid up in master. pedal won,t come up when bled?


fluid is by passing rubbers in master cylinder . replace unit. noise if you are running engine could be air leaking from faulty booster unit

Feb 01, 2013 | Cars & Trucks

1 Answer

1992 olds regency ninty eight. Break pedal seems to go down futher than it should when applying. when stopped at a light brake pedal seems to slip going further down some. Checked for leaks on brake lines...


if master cylinder is bad. the pedal will go to floor running or not.when the pedal goes down at a standing stop it is usually the master cylinder thats bad. and losing vacuum. thats if there are no other leaks at wheel cylinders etc. if putting on a new master cylinder, do not forget to bench bleed it! heres how. put the master cylinder in the vise, fill it full of fluid then pump the plunger with a dowel or something soft as to not ruin plunger part.do not let it run dry ! when fluid comes out from master cylinder and no more air is in it. fill it up and put on car. heres what I do! remove the lines from old cylinder on car. as long as you do not lose any fluid doing this, there is no need to bleed air from brakes when done. after on car make sure master cylinder is full of fluid. start the car and pump the brakes a few times, then you should be all set.

Aug 29, 2011 | 1992 Oldsmobile Ninety Eight Regency

1 Answer

My brake peddel is spongee-soft, and goes to the floor if i prees hard?


when you push pedal hard & pedal goes to floor does brake light come on?
assuming brake fluid leval is ok & didnt run empty have you checked for a leak?
pulling all wheels & inspecting brakes,cylinders, calipers,& lines for leaks.
does the pedal pump up & feel ok with engine running?if so there is air in the system
if it does'nt change the way the pedal feels & no leaks are found & brake linings are ok & adjusted
properly than your master cylinder is leaking internally & needs to be replaced

Jul 05, 2011 | 2001 Chevrolet Silverado

2 Answers

How to bleed the brakes on a1999 chevrolet venture van instaslled new brake pads on front tired to bleed brake pedal all the way up when van not running - goes to floor when van is running


Start with brake in the rear that is the farthest away from the master cylinder ( if your master cylinder is on drivers side start with passenger rear,pump up brake pedal until hard have someone else open bleeder valve until air or fluid squirts out,while holding brake pressure even if goes to the floor dont release pedal until bleeder valve is tightened or you will **** air back into the line,do this several times making sure you get a full stream of brake fluid and no air,continue to other rear wheel and then proceed to front wheel furthest from master cylinderand then final wheel. if you still don't have brakes change master cylinder and bleed all brakes again.

Jul 05, 2010 | 2000 Chevrolet Venture

3 Answers

While driving my 1994 Honda Accord the brakes went out. I can only get the car to stop if I press the brake pedal all the way down to the floor. When the car is shut off and I pump the brake pedal, I can...


There may be air in the lines. Bleed all your brakes starting at the farthest wheel from the resevoir, and finishing at the closest one. Try the pedal after its bled. If the pedal still feels soft or travels to the floor there may be a pinhole leak that may be spraying on the underbody of the car, or the seals in the master cylinder are gone filling the vacuum booster(if equipped). Air compresses more than oil so if bleeding works that may be the problem.

Feb 21, 2010 | 1994 Honda Accord

1 Answer

Excessive brake pedal travel and 'soft' brakes


the brakes have to be bleed you wrote that when you start the car the pedal goes to the floor that means the booster is working fine take it back and tell them you want the brakes bleed

Nov 14, 2008 | 2003 Honda Accord

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

Not finding what you are looking for?
1999 Chrysler Town & Country Logo

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...