Question about 2002 Honda CR-V

1 Answer

How do I replace a Tail Light on a 2002 Honda CRV

I have removed the light fixture but how do I disconnect the wires?

Posted by on

  • Anonymous Mar 15, 2014

    How to remove inside panels between doors to replace fixtures?

  • Anonymous Mar 26, 2014

    TAIL LIGHT FIXTURE

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Pretty simple just remove the light fixture then you just have to remove the bulbs from the fixture and wire assembly remains intact then just fit the same bulbs in to the new light fixture without removing the wire assembly.

Posted on Jan 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the tail light fixture to replace brake bulb?


Four of them ?
Remove the tail lamp housing to body screws. Carefully slide the tail lamp housing rearward away from vehicle. Disconnect the tail lamp housing electrical connector. Remove the tail lamp housing from the vehicle.

Mar 22, 2015 | 2002 Saturn VUE

2 Answers

2007 tail light fuse location honda crv


I had this problem with my 2007 Honda CRV -- all the lights worked EXCEPT the tail/running lights and the license plate light. The other tail lights worked -- brake, reverse, indicators, and hazards. Front headlights also worked, but when the headlights went on the back tail lights did not (not to safe for driving at night!!)
The fuse was #15 in the interior fuse box (under the dash driver side) with the label "small exterior lights" ( also check fuse #19 labeled "small lights main"). The cause of my problem, I believe, is a bad or lose wire in my license plate light.

Jan 16, 2012 | Honda Civic Cars & Trucks

1 Answer

Honda crv 2000, no instrument panel light, no park , front fog or tail lights. checked fuse(ok) but replaced anyway


check for loose negative wire on battery terminal, tighten if loose,
check your ignition switch, the accesories wire (positive) if loose/ re-connect it.
check for loose accesories harness wire- repair if nescessary.

Sep 17, 2011 | Honda CR-V Cars & Trucks

1 Answer

Replacing drivers side tail light


here not bad to replace. Can be purcahesed for $80 from this site. Instructions can also be provided by this site,

http://www.1aauto.com/1A/HeadLights/Hyundai/SantaFe/1ALHL00978/261686?utm_source=google_base&utm_medium=cpc&utm_campaign=google_base_yr

Basicly, remove bulbs, disconnect wiring harness from bulbs. Remove nuts that hold lamp in and replace with new fixture. Should go ahead and replace buls while you are in there.

May 30, 2010 | 2001 Hyundai Santa Fe

1 Answer

Could someone please tell me what the coloured tail light wires respond to on a 2004 honda crv. eg white = earth , yellow = right blinker. Or even where i could locate a wiring diagram for this vehicle....


THE EASIEST WAY TO FIGURE OUT WHICH WIRE DOES WHAT IS TO USE A TEST LIGHT . ATTACH A TEST LIGHT TO A MATEL SURFACE NEAR THE TAIL LIGHTS, THEN REMOVE YOUR DIRECTIONAL BULB, TURN ON YOUR DIRECTIONAL AND CAREFULLU TOUCH THE TESTLIGHT TO ONE OF THE TWO CONTACTS IN THE RECEPTICLE THEN WRITE DOWN THE COLOR OF THE COROSPONDING WIRE THAT TRIGGERS THE LIGHT.

Sep 08, 2009 | 2004 Honda CR-V

1 Answer

How to disconnect the electrical plug from the old tail light on my 2002 Grand Cherokee Jeep.


looked thru manual and there is nothing I can find. I'm sure it's a twist lock fixture. I've had mine out a few times to change lamps but don't remember exactly. Look at it in very good light and you'll figure it out.
Rudy

Apr 01, 2009 | 2002 Jeep Grand Cherokee

1 Answer

2004 Honda CRV tail lamp assembly


remove the grommet the wires go through, you may be able to reach the connector or remove inner trim panel.can you not use the original loom and just change the light unit?

Dec 29, 2008 | 2004 Honda CR-V

1 Answer

Tail light out


Open the rear hatch. There are two screws towards the inside. Unscrew these and remove the housing.Turn the bulb holder 1/8 turn counterclockwise and pull out. Push in on the bulb and turn it counterclockwise, then pull the bulb out of the holder. Replacement is exact reverse of removal.

Nov 22, 2008 | 1998 Honda CR-V

1 Answer

Tail / brake light lens replacement


remove the inner plastics on that side and uplug and remove the 10-15 ten mm bolts remove the light and reinstall there maybe some weatherseal holding the light also just yank it out please rate -jeff

Sep 01, 2008 | 2005 Honda CR-V

Not finding what you are looking for?
2002 Honda CR-V Logo

Related Topics:

386 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...