Question about 2002 Jaguar X-Type

1 Answer

Jaquar X Type Oxygen Sensor

Where is the oxygen sensor (or sensors) located on a 2002 Jaguar X Type 3.0 V6 ? Are they hard to change?

Posted by on

  • supt Jan 12, 2009

    Where is the oxygen sensor (or sensors) located on a 2002 Jaguar X Type 3.0 V6 ? Are they hard to change?

  • Anonymous Apr 20, 2009

    where are the o2sensors at on a 2.5 jag

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 133 Answers

Two at the front on the exhaust cat and two on the rear, and yes if there tight

Posted on Dec 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

P1133/oxegen sensor


MAKE SURE THE CONNECTIONS AT THE SENSOR ARE GOOD,ALSO CHECK FOR VACUUM LEAKS,HERE'S A LINK TO YOUR CODE,THE OLD SENSOR MAY BE GOOD,JUST A VACUUM LEAK, P1133 Chevrolet HO2S Insufficient Switching Bank 1 Sensor 1

Oct 17, 2015 | 2002 Isuzu Rodeo Sport S 3.2L V6 Hard Top

2 Answers

Check engine light on, 0430 code


This code is not uncommon with the X-Type, a dealer will recommend replacing the Cat. very expensive. get a 1" spark plug extender and drill a 1/2 hole through it and screw it into the lower O2 sensor hole for bank 2 (rear of the engine) and then screw the O2 sensor into it, reset the code and you should be all set.

Jan 04, 2014 | 2002 Jaguar X-Type

1 Answer

Oxygen sensor 1


the front sensor B1S1 is in front,
that means its not behind the catalyst converter device.
is this a v6? , it has 2 , #1 sensors
bank 1 sensor 1
and
bank 2 sensor 1
double trouble, post engine type, V6?

Apr 13, 2013 | 2002 Suzuki XL-7

2 Answers

Where is the bank 1 sensor 1 o2 sensor located in a 2006 hyundai sontata gls v6?


The bank has to do with which side of the engine. The 'Sensor 1' indicates that it is upstream of the catalytic converter.

Heated Oxygen Sensor Removal & Installation Heated Oxygen Sensor (Front) (2.4L) hyundai-04-24-5822.gif

Heated Oxygen Sensor (Rear) (2.4L) hyundai-04-24-5823.gif

Heated Oxygen Sensor (Bank 1/Sensor 1) (3.3L) kia-04-00-5213.gif

Heated Oxygen Sensor (Bank 1/Sensor 2) (3.3L) kia-04-00-5214.gif

Heated Oxygen Sensor (Bank 2/Sensor 1) (3.3L) kia-04-00-5215.gif

Heated Oxygen Sensor (Bank 2/Sensor 2) (3.3L) hyundai-04-33-5855.gif

prev.gif next.gif

Jan 13, 2011 | 2006 Hyundai Sonata

1 Answer

Ihave a 2003 Jaguar S-Type, What do PO133, PO153 and P1000 codes mean? Afriend said oxygen sensors; how to change the oxygen sensor for a 2003 Jaguar S-Type?


You might check this site out for Jag codes. Oxygen sensors can be a sticky job, they're screwed into exhaust and can literally weld themselves in place. Plus in most cases you need special wrench/socket to get around the sensor. (they can be a real pain)

http://www.obd-codes.com/

Jan 04, 2011 | 2003 Jaguar S-Type

1 Answer

Have a oxygen sencor and dont know were to put it in at thanks....


WELL WHICH OXYGEN YOU REPLACING THE UPSTREAM OXYGEN SENSOR MOUNTED IN EXHAUST MANIFOLD AND THE DOWN STREAM OXYGEN SENSOR LOCATED IN THE EXHAUST SYSTEM AFTER THE CATALYTIC CONVERTER .YOU NEED A OXYGEN SENSOR SOCKET TO REMOVE IT.TO REMOVE OXYGEN SENSOR CRANK VECHICLE TO GET OXYGEN SENSOR HOT BECAUSE HARD TO REMOVE WHEN COLD.BECAREFUL DONT GET BURN ON EXHAUST MANIFOLD WHEN REMOVING OXYGEN SENSOR.AND WHEN INSTALLING NEW OXYGEN SENSOR USE ANTI SEIZE COMPOUND ON SENSOR THREADS.BUT MOST OF THE TIME NEW SENSOR WILL HAVE ANTI SEIZE COMPOUND ON IT.

Dec 08, 2010 | 2002 Jaguar S-Type

1 Answer

Where is the rear "b2 s2" oxygen sensor located in a Jaguar 2003 xtype 2.5liter car? There are 4 oxygen sensors -- one in the front catalytic converter and one next to it by or in the exhaust manifold and...


Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

Some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Hope helps (remember to rate this).

Oct 06, 2010 | 2002 Jaguar X-Type

1 Answer

I need a diagram of the exhaust system on a Mazda 626


0996b43f80203328.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2000 MPV

1 PCM 2 Mass air flow (MAF)/intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Fuel tank pressure sensor 5 Engine coolant temperature (ECT) sensor 6 Crankshaft position (CKP) sensor 7 Camshaft position (CMP) sensor 8 Knock sensor 9 Heated oxygen sensor (HO2S) (front, LH) 10 Heated oxygen sensor (HO2S) (front, RH) 11 Heated oxygen sensor (HO2S) (rear, LH) 12 Heated oxygen sensor (HO2S) (rear, RH) 13 EGR boost sensor 14 Power steering pressure (PSP) switch 15 Main relay


0996b43f8020330c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2001 MPV

1 PCM 2 Mass air flow (MAF)/Intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Engine coolant temperature (ECT) sensor 5 Crankshaft position (CKP) sensor 6 Camshaft position (CMP) sensor 7 Knock sensor 8 Heated oxygen sensor (HO2S) (front, LH) 9 Heated oxygen sensor (HO2S) (front, RH) 10 Heated oxygen sensor (HO2S) (rear, LH)* 11 Heated oxygen sensor (HO2S) (rear, RH)* 12 EGR boost sensor


0996b43f8020330f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart- 2002-06 MPV

May 22, 2010 | 2004 Mazda MPV

2 Answers

Where is the O2 sensor located on the 2003 V6 All Wheel Santa Fe and how dificult is it to replace?


Hyundai Santa Fe 2001-05
Heated Oxygen Sensor (H02S): The sensors are located in the exhaust system. On some vehicles, one sensor is located up at the exhaust manifold(s) and the other sensor is located down at the catalytic converter. On other vehicles, both sensors are located down at the catalytic converter.

d2217fa.jpg

How to Replace an Oxygen Sensor
Parts:
1. Oxygen Sensor
2. Oxygen Sensor

Tools:
1. 3/8 in. Drive Ratchet
2. Multimeter
3. Oxygen Sensor Socket
4. Combination Wrench Set
5. Crimp Tool
6. Socket Set
7. Scan Tool

Steps:
Step 1 * Park the vehicle on a level surface. Set the parking brake and open the hood.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.
o Tip: Always make sure the struts on the hood can fully support the weight of the hood so that it does not close on you while working. The use of a hood prop can securely hold it in place.

Step 2 * With the engine off and cool, locate the defective oxygen sensor in the exhaust manifold or pipe. If necessary, lift the front of the vehicle and support it with jack stands.
o Tip: Most vehicles have multiple oxygen sensors. How many sensors, depends on the model year and type of engine.

Step 3 * Disconnect the wire connector at the defective oxygen sensor.

Step 4 * Remove the oxygen sensor from the exhaust system.

Step 5 * If you are installing a universal oxygen sensor, cut off the connector from the original sensor and splice the connector wires to the new oxygen sensor. Follow the manufacturer’s instructions supplied with the sensor.

Step 6 * For threaded oxygen sensors, apply anti-seize compound to the threads and install the new sensor.

Step 7 * For flange mounted oxygen sensors, install a new gasket and tighten the mounting bolts.

Step 8 * Reattach the wire connector from the sensor.

Step 9 * If necessary, connect the OBD I/II scanner and erase the fault code.

Hope help with this (remember rated and commented this help) Good luck.

Mar 01, 2010 | 2003 Hyundai Santa Fe

Not finding what you are looking for?
2002 Jaguar X-Type Logo

Related Topics:

3,684 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70347 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

447 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...