Question about 1992 Eagle Talon

1 Answer

I dont know how to set my timing on my car - 1992 Eagle Talon

Posted by on

  • yadayada
    yadayada May 11, 2010

    Post your question one time please, this is a free forum and redundant posting take time away from answering other folks question's.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

If you dont know take t to the shop. cuz you might jux time your car wrong and haveto replace a wole new moter

Posted on May 04, 2009

  • lue vue May 04, 2009

    i know it costs a lot but to have a motor replace is more

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My son in law removed the cam timing chain to check the rocker arms. we need to know the gap setting for the rockers


DONT BLAME YOR SON IN LAW! LOL BY THE WAY, GET THE EXACT SPECS FOR THE TIMING MARKS & ROCKER ADJUSMENTS FROM THE DEALER IF NA. IM'M SURE HE KNOWS OF THE NASTY WRONG POSSIBILITIES OF WRONG SPECS FOR THAT ONE. DONT TRUST THE INTERNET!

Feb 15, 2016 | Cars & Trucks

1 Answer

1990 ford ranger 2.3 timing belt pully diagram


Set the crank to TDC using the timing marks, look for a mark on the cam pulley and a mark on the head, line those marks up and put on the belt

Feb 12, 2013 | Cars & Trucks

1 Answer

My 1994 pontiac bonneville wont start and i dont know how to pull the codes without a tool, dont know which pins too cross


Jump the two pins in the upper left corner of the connector. Then turn on ignition ( dont crank car ) , codes are delivered in flashes and short and long pauses. First code will be 12 ( flash , short pause 2 flashes , long pause) it will repeat 3 times. Any codes stored will repeat 3 times each after that , the list of stored codes will end with another set of 12's.So a code 38 will be 3 flashes-short pause - 8 flashes.Good luck

Jan 24, 2011 | Pontiac Bonneville Cars & Trucks

1 Answer

I am trying to check my timing for a 1989 f-150 with a 351w with fuel injection. i have an induction timing gun but i dont know what part of the computer i am supposed to disconnect . There is no vacumm...


First clean the balancer and find the timing mark, mark it clearly with a chalk ,or crayon, or liquid paper, 10 degrees BTDC. Get the engine warm, now remove the timing connector ( Its a little gray plastic connector near the distributor, its 2 pins) disconnect that , then start the engine and set the timing. Tighten the distributor, Check it again, if ok, turn eng off and reconnect the timing connector. you are done.

May 10, 2010 | 1989 Ford F 150

2 Answers

How do i know if i set the timing belt right?


u must hav a haynes manual--dont start it if its not correct cause u cud warp the valves and then ud be changin motors

Apr 18, 2010 | 1991 Honda Accord

1 Answer

I NEED DIAGRAM TO HOW TO SET THE TIMING ON 03 HONDA PILOT


I DONT KNOW HOW TAKE OFF FROM EXTRA SPARE I DONT KNOW WHERE IS LOOSE SPARE TIRE UNDER REAR BACK

Jan 14, 2010 | 2003 Honda Pilot

2 Answers

Opel Corsa timing belt replacement


You need to find the timing marks on both crank and cam pulleys, set it, then take of the belt ane dont let any pulley move! Put on new belt and set the tension of the belt.

Jul 31, 2009 | 2000 Acura Integra

1 Answer

I dont know to how many degrees before dead center to set my cars timing?


your timing should be set at 10 degrees with the TE1 and E1 pins jumped in the diagnostic connector located under the hood (should be set at idle speed)

May 31, 2009 | 1991 Toyota MR2

1 Answer

How do u set the timeing on 96 grand prix GTP with 3.4L V6 DOHC?


if it was me i would go to my local library and get the pictures and diagrams showing me how to do it and at the same time you will know what you are looking for.

Mar 02, 2009 | 1996 Pontiac Grand Prix

Not finding what you are looking for?
1992 Eagle Talon Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Stewart Dibbs

Level 2 Expert

267 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...