Question about 1996 GMC Sonoma

1 Answer

96 gmc sonoma will not accelerate over 30 mph

Code read egr valve. put new one in but still having the same issue. could it be the catalytic converter?

Posted by on

  • Allison Hulbert May 11, 2010

    do you remember what the code was

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

It very well could be the cat usually that can make the vehicles computer throw the wrong code

Posted on Feb 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2004 Mazda V- 6 EGR valve blew out the side. I


The fact that the EGR valve "blew out" may indicate excessive exhaust pressure. You could have a partially blocked catalytic converter. This will cause excessive back pressure and loss of power on acceleration.

Sep 17, 2014 | Cars & Trucks

1 Answer

My 96 GMC Sonoma pickup is running, but only 30 mph what could be wrong? I have changed the fuel filter


Bad egr valve? Ignition coil/distributor/ignition wires/spark plugs? How many miles on it?

Sep 02, 2013 | 1996 GMC Sonoma

1 Answer

96 cutlass supreme will not pass emission in ut. what should I do? KOER failed, trouble code po401


cleanout egr valve and troutle body . Or replace egr with new one, clean, check vacumm lines , check for clogged check , depending on modle of car you can pippoint problem as some have a common part problem depeding with make of car. But all have to do with exaust system. Insufficient flow exaust flow. Im not an expert, all I know it is related to this, I have it myself so im googling it.

Ford EGR valve

The OBDII fault code P0401 means that the engine computer has detected that the Exhaust Gas Recirculation (EGR) system flow is insufficient. Read more how the EGR system works below. What could cause the code P0401 - clogged or restricted EGR passages
- faulty EGR valve
- EGR valve stuck closed
- problems with the DPFE sensor (Ford)
- problems with hoses to the DPFE sensor (Ford)
- problem with the EGR vacuum switching valve (Toyota)
- clogged catalytic converter
- carboned up EGR temperature sensor
- vacuum supply issues at the vacuum-operated EGR valve
- electrical problems with the EGR valve control circuit
- engine computer problems
helpful website helps you with pinpoint and sou;ution related to auto make and model shows you most common cause of code reading.
www.samarins.com

Apr 16, 2013 | Cars & Trucks

1 Answer

2.2 litre 1995 gmc sonoma idles rough no trouble code. found hole i brake booster vaccum line fixed that. replaced and changed fuel filter, idle air control valve, got spark at coil packs, put new spark...


Three things you should check using a good code checker which can read sensor outputs - the throttle position sensor (TPS), the mass air flow sensor (MAF) and the EGR valve. While you are at it, replace the PCV valve.

Jul 30, 2017 | 1993 GMC Sonoma Club

1 Answer

97 buick lesbre shakes while acceleration *egr valve code*


vaccum leak,EGR may is good,check tow lines near thermostat,for crack

Feb 06, 2013 | Cars & Trucks

1 Answer

1996 GMC Sonoma Acceleration problem!


If the check engine light is on I would have that checked first. The trouble codes in the computer will help point you in the right direction for troubleshooting.
You could have a sticking fuel injector, or an ignition problem, or both.

Dec 18, 2012 | 1996 GMC Sonoma

1 Answer

96 sonoma running too rich with p1406 code


P1406 EGR Valve Pintle Position Circuit Fault
This code is usually caused by carbon buildup in the EGR valve. The carbon deposits prevent the valve from closing completely.

After removing the EGR valve, clean the pintle seat area of the valve and the corresponding passageway in the engine.

or simply replace the EGR valve.

Hope this helps!

Mar 07, 2012 | 1996 GMC Sonoma

1 Answer

My 98 sonoma truck runs but lacks power with service engine soon light on .trouble code reads po300 cylinder misfire detected (random) what dose this mean


See also: P0300 diagnostic code @ OBD-Codes.com
Possible Causes:
Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect Fuel Pressure
EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues

Mar 13, 2011 | GMC Sonoma Cars & Trucks

1 Answer

1996 gmc sonoma 2.2 engine


For 1996 GMC Truck Sonoma 2WD 2.2L SFI OHV 4cyl
The EGR Valve is located under hood, center, rear engine area, mounted top rear driver side of engine.

c30f299.jpg

Fig. 11: Unfasten the EGR valve retaining bolts...


b24c0c0.jpg


Fig. 12: ...then remove the EGR valve from the vehicle


I really hope help with this (remember rated and comment this post).


Mar 10, 2010 | 1996 GMC Sonoma

Not finding what you are looking for?
1996 GMC Sonoma Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

82285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...