Question about 2005 Toyota Corolla

1 Answer

2006 toyota corolla left headlamp replacement

Seek correct information on how to remove headlamp assembly to replace headlamp

disconnect wiring harness safely

seems like there are at least two phillips head screws that are used to mount or adjust (level) the beams from the assembly?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Start in the back the hol assebly comes out

Posted on Dec 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a 2006 scion blower motor


cab heater a/c blower?
did you apply 12vdc to it directly and its dead>?
scion not corolla (corolla is easy)
tc,xa or xb>>>> no clue, so will look at tc.

but no matter what, i hot wire the blower, first. everyone does.
and the FSm too, it tells you step by step how to do the test.
sorry if all this is old hat, most here dont know this.....
if the blower works hot wired, its good.

ok the FSM covers this job, getone.
or, login in to alldata.com and read how.
that is what we do, so we can plan our time.

TC
. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL WARNING Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY UPPER
  • Remove the instrument panel sub-assembly upper
3. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY LOWER
  • Remove the instrument panel sub-assembly lower
4. REMOVE ECM
5. REMOVE AIR DUCT
6. REMOVE BLOWER ASSEMBLY

it looks like the blower just drops out the bottom, did you look?
it has 3 screws hold the motor assy to the main casing.
and the plug is there pin 2 is hot, pin 1 is ground
hot wire pin 2.
facing motor, with conn, at 12pm, pin 2 is LEFT.
the FSM shows a photo of that. and the full steps.


Feb 09, 2014 | 2006 Toyota Corolla

1 Answer

How to remove headlamp assembly 2006 Ford Five Hundred


bulb replacement?

You may be able to clear bumper cover by pusihing down while pulling out lamp.

Please rate.
---------------------------

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005
Headlamp Assembly - Five Hundred, Montego adobe.gif Printable View (211 KB) n0050703.jpg
Item Part Number Description 1 W702706 Top headlamp assembly bolts (2 required) 2 W704551 Side headlamp assembly bolt 3 W702706 Front headlamp assembly bolt 4 13005/13006 Headlamp assembly (RH/LH)
Removal
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 4 bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
Installation
  1. Connect the electrical connectors and position the headlamp assembly in place.
  1. Install the side headlamp assembly bolt.
    • Tighten to 11 Nm (8 lb-ft).
  1. Install the front headlamp assembly bolt.
  1. Install the top outboard headlamp assembly bolt.
  1. Install the top inboard headlamp assembly bolt.
  1. Install the front bumper cover. For additional information, refer to Section 501-19.

Aug 03, 2011 | Ford Five Hundred Cars & Trucks

1 Answer

Need help changing out the low beam on drivers side of 2006 buick rainier


Removal & Installation
Bulb Replacement
To Remove:

CAUTION
Halogen bulbs contain pressurized gas.
Mishandling a bulb may result in the bulb shattering into flying glass
fragments.

CAUTION
Make sure to wear eye protection when
handling a halogen bulb.

CAUTION
Do not touch the glass of a halogen bulb,
only handle the bulb by the base.

CAUTION
Do not allow a halogen bulb to come into
contact with dirt or moisture.

CAUTION
Make sure to dispose of a used halogen bulb
properly.

CAUTION
Do not allow children to handle halogen
bulbs.


  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket
    counterclockwise.

To Install:


  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket
    clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.

Headlamp Assembly
Chevrolet
To Remove:






Headlamp Assembly (Chevrolet)
gm-06-00-1591.gif




  1. Remove the grille from the front of the vehicle.
  2. Release the headlamp assembly retaining tabs.
  3. If equipped, disconnect the headlamp leveling motor connector.
  4. Disconnect the headlamp connector.
  5. Remove the park/turn and side marker bulb sockets from the headlamp
    assembly.
  6. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. Install the park/turn and side marker bulb sockets into the headlamp
    assembly.
  3. Connect the headlamp connector.
  4. If equipped, connect the headlamp leveling motor connector.
  5. Lock the headlamp assembly retaining tabs.
  6. Install the grille onto the front of the vehicle.

GMC, Oldsmobile, Buick, Isuzu, and Saab
To Remove:






Headlamp Assembly (GMC, Saab, Oldsmobile, and Buick)
gm-06-00-1590.gif




  1. Release the headlamp assembly retaining tabs.
  2. Disconnect the headlamp connector.
  3. Remove the park/turn bulb socket from the headlamp assembly.
  4. For GMC, Saab, Oldsmobile, and Isuzu vehicles, remove the side marker bulb
    socket from the headlamp assembly.
  5. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. For GMC, Saab, Oldsmobile, and Isuzu vehicles, install the side marker bulb
    socket into the headlamp assembly.
  3. Install the park/turn bulb socket into the headlamp assembly.
  4. Connect the headlamp connector.
  5. Lock the headlamp assembly retaining tabs.


prev.gif next.gif

Oct 28, 2010 | 2006 Buick Rainier

1 Answer

How can I replace an alternator in a Toyta RAV4 2006?


if i recall correctly about a 30 - 40 minute job its mounted on top of the engine so easy to get to. theres just a couple of nuts and bolts to remove alternator along with wiring on the back of it. JUST REMEMBER TO DISCONNECT BATTERY EARTH LEAD FIRST then reconnect when new alternator fitted, ensure alternator drive belt is tensioned correctly also. hope this helps

Jul 17, 2010 | 1991 Toyota Corolla

1 Answer

How do I replace headlight bulb for my toyota corolla 1998?


Open up the hood, and go in behind the fixture where the light is located. Grasp the headlamp electrical connector socket (with wires coming out of it) and disconnect it by pulling straight back. Pull off the black, soft rubber protective housing that surrounds the back of the headlamp housing. You will then see a spring clip securing the bulb. Push the clip in and up on an angle and it will release the bulb. Never touch the new bulb with your bare fingers, as the skin-oil you leave will greatly shorten the bulb's life. Place the new bulb assembly into the housing, push the clip in and up again, but in the opposite direction of the first angle to release it and it will lock. Then replace the black rubber housing-cover, plug the electrical connector back in, and you're in business.

Oct 12, 2009 | 1998 Toyota Corolla

1 Answer

How to replace a 2006 toyota corolla blower motor


Hi,
Try the following & I am sure about the results;

Remove two screws on bottom of front face of glove box
Remove Glove box
Heater is just behind the glove box on the right side (the motor points downward and the fan is in a big round shroud).
Un plug the cable bundles that get in the way of removing the blower moter (the motor will come straight down).
There are three bolts holding the blower assembly in place, remove them and the blower assembly can be removed (pull downward).

Hook the black wire from the new motor up to the connector were the wire with the line on it (from the truck) was and the red wire from the motor to the solid colored wire from the truck (the wires from the motor had leads that you could slide into the connector from the truck).

Good Luck & Thanks,
Shiv.

Aug 20, 2009 | 2006 Toyota Corolla

2 Answers

How do I replace a 2006 Beetle Headlight bulb?


Under the hood you on the back side of the headlight assembly there is a a small release lever with a lock. Push the lock in and rotate the release lever. Push the headlight assembly out so you can have access to the wiring plug. Disconnect the wiring plug and completely remove the headlight assembly. Now on the back of the headlight assembly is a spring clip and a small screw. Remove the small philips head screw and release the spring clip.

Jun 05, 2009 | 2006 Volkswagen New Beetle

2 Answers

Need belt schematic for 2006 toyota corolla


I can get you a diagram on monday but it goes from the alternator to the power steering pump then around the tensioner pulley then around the crank pulley then to the a/c compressor then pull on the tensioner to give you some slack and slip it on the waterpump.I hope that helps.Let me know if you still need the diagram

Nov 29, 2008 | 2006 Toyota Corolla

1 Answer

How to replace Marker lamp in 1999 Toyota Corolla


Open the hood. Observe the area above the right headlamp, close to the fender. You will see a phillips screw that holds a plastic tab. Remove the phillips screw. After removing the screw, pull the marker lamp assembly towards you. It may be real tight, if it has never been removed before. You need to pull the light assembly out of 2 retention sockets behind the marker lamp. Rotate the bulb socket to get to the bulb, replace the bulb, & slide it back in.Easy job.

Oct 21, 2008 | 1998 Toyota Corolla

1 Answer

Instructions on replacing headlight assembly


96 f150 procedure

Headlamp Assembly Removal
  1. Remove radiator air deflector from radiator support.
  1. Remove two screws and two nuts retaining headlamp door (13064).
  1. Pull headlamp door from vehicle. Remove three bulbs and sockets.
  1. Disconnect engine control sensor wiring (12A581) from headlamp bulb (13007).
  1. Remove two retainers attaching upper two attachments of headlamp (13008).
  1. Turn horizontal headlamp adjusting screw (13032) completely out of the adjusting nut.
  1. Pull headlamp from vehicle.

Oct 17, 2008 | 1994 Ford F150 Styleside Supercab

Not finding what you are looking for?
2005 Toyota Corolla Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...