Question about 1990 Daihatsu Charade

2 Answers

Can you tell me where the timing mark is for my charade 90 model

Posted by on

  • 1 more comment 
  • tai_ssrg Dec 28, 2008

    hi the whole story is that my car sound like it had no compression it happen when i drove back frm wollongong all of the sudden it jst die on me n i tried to start again it has no compression had to tow it bck to my place pull everything apart found t belt jump teeth thats why i ask for timing mark i fited the t belt back my car still has no compreesion i think the valves has bent so the problem still not solve so can you tell me the torque spec for my cylinder head please i think am gonna have to pull the head off and check if any one can help me out wtih this please do

  • tai_ssrg Jan 02, 2009

    it was helpfull information indeed thank you very much for your kindness

  • James Raymond Williams
    James Raymond Williams May 11, 2010

    Please can you supply me with the engine code and the cc of the engine. Also is it petrol or diesel and if it is single or twin cam. These engines are interference engines and great care should be taken not to move the crank when the belt is removed.

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 272 Answers

I think your valves are bent. As you have mentioned, you will have to take off the head and check the head out for any damage. I can not tell you the torque values but I would recommend that you get a workshop manual from either Autodata or Haynes Manuals bothe have websites. You will find all the information you need in these manuals and they will save you money in the long run.

Posted on Dec 28, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 98 Answers

The timing mark i on the flywheel. There is a portal, that may have a rubber plug fitted. You must pull the hoses on the distributor and block them to stop the vacuum advance while you are setting the ignition timing.

If you are trying to fit a belt you need to line up the crank pulley dimple and the camshaft sprocket dimples. The flywheel dimple is advanced about 5°. This pic shows the dimple and the line is the actual TDC.

This is the valve timing procedure here

Posted on Dec 28, 2008

1 Suggested Answer

gregstobbe
  • 56 Answers

SOURCE: timing mark for charade 90 model 3 cylinder

here is the site for timing marks.
http://www.2carpros.com/car_repair_information/tec_info/1990/daihatsu/charade/1990_daihatsu_charade_timing_belt_diagram_marks.htm
Ps. dont forget to rate my solution please. Thanks.

Posted on Dec 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the trimming marks on a diahtsi charade sedan1984 3 cyl


are you questioning where the timing marks are if so are on the pulley and just behind it so you can see them with a timing light
Does this help?

Aug 18, 2013 | 1992 Daihatsu Charade

2 Answers

Putting spark plugs in a charad 1997 wat is the firing order they go in please


Dont tell me you removed all the wires at once without marking them? :O
The best advise for that is, to remove one wire and plug at a time then replace the plug, and connect the wire back in place to avoid mix ups...
I have spec tables for that car, but you need to help me with the model, whats the year model, 92 or 97?

Aug 19, 2011 | 1992 Daihatsu Charade

1 Answer

I have a 1990 model Daihatsu Charade G102. I had to replace the Head Gasket which i did with a friend via the manual. when we put together it started first time then stalled. It would only keep going if i...


The popping/stalling suggests you guys got your valve timing wrong when re-fitting timing belt. Remove your cover and double-check your timing marks on cam gear and crankshaft gear. Align you timing marks.

Oct 31, 2010 | 1992 Daihatsu Charade

1 Answer

95 charade . where do i find the mark on the


you have a leaking fuel injector if it runs after shut off. if its an other than U.S. model with carberator then the idle is set to high or the fuel shutoff solonoid is stuck/leaking.

May 12, 2010 | 1992 Daihatsu Charade

2 Answers

Can not get timing 2 set on my daihatsu hijet there is dots on timing cogs which timing belt runs on on front of motor but no markings 2 set them at car will not fire


Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for the 1988 Daihatsu Charade 1.0L 3-Cylinder which is the closest to the Hijet. Plus additional Instructional and Directional Diagrams.

Note: the annotated Align Matings Marks located on the engine casing, or the Belt Alignment Marks.
I owned one of these while living in Japan.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1988/make/daihatsu/model/charade/1988_daihatsu_charade_timing_belt_diagram_marks.htm

Apr 02, 2010 | 1988 Daihatsu Charade

2 Answers

TIMING MARKS CAMBELT REPLACEMENT FOR CL-T CHARADE, PLEASE


This is the best I could find for you .. I am unfortunately able to verify the info because I have no personal experience with this car or its engine ...

Mar 14, 2009 | 1988 Daihatsu Charade

1 Answer

Where are the valve timing marks on a 1997 993cc charade


Sorry for the severe delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams for use.

To answer your direct question: (See Diagram 96F14675 on the Link) The Belt Alignment and Align Mating Marks are the keys.
The Crankshaft "pulley" (actually the Sprocket) has the outer Flange (cover) which needs to be removed to see the Timing Mark.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1988/make/daihatsu/model/charade/1988_daihatsu_charade_timing_belt_diagram_marks.htm

Mar 13, 2009 | 1988 Daihatsu Charade

Not finding what you are looking for?
1990 Daihatsu Charade Logo

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...