Question about 2003 Toyota Sienna

1 Answer

2003 Toyota Sienna Vertical Adjustment

I need to adjust the vertical lowbeam headlights. My lowbeams are like highbeams. I keep frustrating other drivers. Factory defaults **** sometimes. Any help is appreciated. Dealership wants 75 dollars to adjust. Thanks.

Regards,

Mike

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Should be adjustment under hood look for place where phillips screw driver goes in and meshes with the lenses to adjust it

Posted on Dec 27, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I got a problem with my Volvo V70 headlights. When i turn on highbeam, the lowbeam reflector adjust itself up, providing more light to the high beam. After i mounted a h9 55w xenon kit into the hi


it may need reset at the dealer to accomodate the new style/type of lamp..unless the cars', original factory setting does not allow for that change to be made.. they can tell you either way..

Dec 24, 2013 | Volvo Cars & Trucks

1 Answer

When I turn on my headlights the lowbeam lights will not come on. I switched the highbeam and lowbeam wires to see if it was the wires or the lights. the lowbeam lights came on when i put the high beam...


It is either the light switch or the headlight relay, I would say first go for the relay as it carries the actual load of the lights. It will not be a fuse, the headlights are fused individually.

May 09, 2011 | 2000 Dodge Ram 1500 Truck

1 Answer

03 ion lowbeams wont work highbeams do have


The dark blue wire is the ground wire for the low beams and your pink is the ground for the high beams.

When you touch that wire to ground the lights should come on. If not there is a short/break in the wire somewhere

Double check your pink wire to confirm that it is supposed to be a ground signal.

Apr 03, 2011 | 2003 Saturn ION

1 Answer

How do you adjust the highbeam headlight on 08 G6


there is no separate for the highbeam. Basically, you are forced to use one screw for both and have to compromise

Nov 16, 2009 | 2006 Pontiac G6

1 Answer

My left headlight highbeam light works and the lowbeam don't why


the filament on the low beam burnt out. but the high beam didn't. You have a filament for each. 1 for high beam and 1 for low beam in the same light bulb. You need a new head light.

Sep 07, 2009 | 1998 Ford Windstar

2 Answers

I have a 1998 landrover freelander how do i adjust the headlights ?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jul 14, 2009 | 2004 Land Rover FreeLander

1 Answer

Lowbeam


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Jul 03, 2008 | 2000 Toyota Sienna

Not finding what you are looking for?
2003 Toyota Sienna Logo

Related Topics:

641 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

83514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22393 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...