Question about 2002 Nissan Sentra

1 Answer

Removal of the Door Panel from a 2000 Nissan gte car

Thanks for any help. I have the clips off of the bottom of the panel. Something around the handle of the door is still holding the door panel on. I am trying to replace one of the electric window switches on the drivers side consol.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the rear sliding door interior panel on 2001 Nissan Quest?


Mostly clips, screws hold the handle on and bezel around it has clips that can carefully be pried off.. A door panel tool should be used to enage and pry panel clips off

Aug 22, 2014 | 2001 Nissan Quest

1 Answer

Removal of front door panel 2000 Cadillac Deville


Usually a couple screws at the door handle and plastic clips along the sides and bottom. I strongly suggest getting the tool for the clips. It's cheap and you don't want to break the clips. Once the panel is free from the door it slides up and off.

May 27, 2012 | 2000 Cadillac DeVille

1 Answer

How do u remove the drivers side door panel to fix the window


YOU NEED CLIP REMOVAL TOOL TO REMOVE WINDOW CRANK HANDLE.YOU NEED DOOR PANEL FLAT TOOL REMOVE DOOR PANEL HATE TO SAY DOOR PANEL HAS AT LEAST 8 CLIPS LOCATIONS 4 CLIPS AT THE BOTTOM PANEL 2 CLIPS ON BOTH SIDES DOOR PANEL. YOU HAVE TO REMOVE 2 SCREWS HOLDING DOOR PULL CUP.YOU HAVE RELEASE CLIP BEHIND DOOR HANDLE USING TRIM TOOL.IF YOU HAVE TROUBLE GETTING DOOR PANEL OFF.HAYNES REPAIR MANUAL CAN HELP.

Oct 07, 2010 | 2004 Chevrolet Cobalt

2 Answers

I need to remove the door panel on my 2000 PONTIAC BUT I DONT SEE ANY SCREWS


look for tabs or look like plugs, pull those w/screwdriver bottom panel you'll need to insert scrw drvr in @ pop out @ it has pull tabs that pop back in on reinstall also look for screws at door pull handle

Aug 14, 2010 | Pontiac Grand Prix Cars & Trucks

1 Answer

Need to remove door panel drivers door bonneville 1999. my goal to replace outside mirror. thank you,


Door panels are about the same they have always been.
You first remove the things attached, like handles, etc.
Most have screws, either recessed or covered by plastic plugs.
Door handle may have spring clip that requires a hook or special tool for, but you can improvise. Just push panel in to get a better look around handle shaft.

Once you have all the extra stuff off, then pop all the little plactic or metal clips around the front, back and bottom edges. It helps to use something a little wide, to not scratch or break panel. Each clip snaps into hole.

But the top is different, and hooks over the metal door inner shell. It has to be lifted upwards, after unscrewing door lock button, if there is one. The bottom of the panel has to be held out enough to clear handle shafts as you lift up.

Apr 20, 2010 | 1999 Pontiac Bonneville

1 Answer

I need to know how to replace the driver side door handle on a 1995 Nissan Pathfinder?


If you can get a trim removel tool it helps to keep from breaking the clips. Next, it is just a matter of taking out all the phillips screws. There is one in the handle area, under the little center cover. There is one at the front of the door panel and another under the electrical switch. Once all the screws are out the clips still hold the panel on and that is where the trim removal tool helps. It looks like a flat tool with a recess to get around both sided of the clip. You just slide it in and pry out and that way the clip or door panel does not get broke.

I like to have a helper so when the panel comes all the way off you have someone to hold it whild you remove the connectors to the wiring. Also, when you get all the clips off you will need to lift up to get the panel off the window ledge.

Two screws under the handle mine is snapped off.
Remove the door panel, disconnect the linkage to the handle and remove 2 screws that hold the Handle on.

Hope this help.

Mar 31, 2010 | 1995 Nissan Pathfinder

1 Answer

2000 cadillac deville remove door panel


2000-2001 Deville Door Panel Removal:

1. Position window fully downward and ensure manual lock knob is in unlock position.
2. Disconnect locking clip at front of manual lock knob, by insertingsuitable flat bladed tool into top service notch.
3. Remove manual lock knob.
4. Remove inside handle bezel by holding inside handle to open position, inserting sutiable flat-bladed tool at front lower corner and prying outward.
5. Remove bezel.
6. Remove inside door handle mounting screw.
7. Disconnect eight retainers around outside edges of door trim panel using clip zip tool No. J-36796, or equivalent.
8. Slide door trim panel upwards to release alignment datums, eight retainers, armrest steel retainer clips and inner belt mouldings (see fig #7 amd #8).
9. Disconnect electrical connector(s).
10. Reverse procedure to install.

23785ad.jpg

Hope this help (remember rated this).

Mar 28, 2010 | 2000 Cadillac DeVille

1 Answer

2000 chevy 1500 door panel removal with manual windows and locks?


to remove window handle get a hanger and put a small bend in it slide it behind the handle and hook the clip and pull the handle will come off. purchase a panel removal tool to pop the clip out of the door. and lift on panel and it should slid off.

Feb 09, 2010 | 2000 Chevrolet Silverado

1 Answer

Anywhere to find a breakdown to change the door handle that broke off on a 94 pathfinder?


Very easy to do...I have a 1990 and they are interchangeable....88-94: Door Panel
  1. Fully lower the door glass.
  2. Remove the arm rest, door lock knob and inside door handle escutcheon.
  3. For vehicles with manual windows, remove the regulator handle which is retained by a spring clip.
  4. Gently pry the door panel away from the door.
57cc694.gif
Interior side and floor trim removal procedures-Pathfinder

4c380d2.gif
Remove the lock button first before removing the door panel

e5a8f97.gif
Remove the plug to gain access to door panel retaining screws

54604ec.gif
Remove the trim cover

eec4f16.gif
Remove the door handle trim

09f640c.gif
Remove the power window switch trim panel

44a5e00.gif
After loosening the power window switch trim panel, disengage the electrical connection

530cf7c.gif
Remove all the necessary trim panels before removing the door panel clips

791f0b4.gif
View of the door panel retaining clip-clip must be installed in the hole straight

690538f.gif
Make sure the watershield plastic is in place before installing the door panel

Installation is the reverse of removal.

Dec 10, 2009 | Nissan Pathfinder Cars & Trucks

1 Answer

Drivers side door on my jeep cherokee will not open from inside


most likely the inner door handle has a broken hooking tab for the rod to the latch plate.most door panels are held in place with a few screws around the door pull handle and arm rest than most of the sides and bottom of the door panel are held by plastic snap clips. with a large straight blade screw driver start at a corner of the door panel , slide the blade of the screw driver under the edge of the panel and lightly pry out untill you lossen up one of the clips than slide along the screw driver to the next clip , keep going till the panel is lossened up.

Mar 29, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2002 Nissan Sentra Logo

432 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...