Question about 1991 Jeep Wrangler

1 Answer

1991 wrangler 4x drive

Sometimes when i put my jeep in 4 wheel drive, the front wheels move to the right and it takes some strength to move them straight. What causes this?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Its the automatic locking hub mecanizm replace with after market manual hubs and that should be the end of that

Posted on Dec 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 4 wheel drive does not work on my jeep


The term four-wheel drive typically describes larger passenger vehicles that may allow the driver to manually switch (sometimes with an automatic option) between two-wheel drive mode (if available) for streets and four-wheel drive mode for low-traction conditions such as ice, mud, snow, or loose gravel. It may not -always- work but is very reliable.


-------------------------------------------------------------------------------------------
FGTech Galletto 2-Master EOBD2 V51 BDM-TriCore-OBD

Dec 17, 2012 | 1992 Jeep Wrangler

1 Answer

I have a 95 jeep wrangler when in four wheel drive the right front and left rear are the only wheels that spin


thats correct in order to make all 4 drive you have to put lockers in it.But then you cant drive it on pavement with it locked in.

Nov 04, 2012 | 1992 Jeep Wrangler

1 Answer

1991 Jeep wrangler 2.5 standard shift.vacumn lines from transfur case to front drive axle.we need a picture of where each vacumn hose goes. a print out of the colors. thank you


i just boought a 1992 Jeep Wrangelr sport with a chevy 305 V8 and its a automatic with a standard 4 wheel drive and i put in 4 wheel drive and the front tires wont move what is wrong????

Mar 11, 2010 | 1990 Jeep Wrangler

1 Answer

1991 jeep wrangler front drive shaft isnt turning. Once in a while gears will grind but front diff isnt working


you have a vacumn actuator on the passenger side front axle tube that engages your front axle when put in four wheel drive. those are notorious for not working

Feb 01, 2010 | 1992 Jeep Wrangler

1 Answer

I have a 1987 jeep wrangler and it will not shift into 4 wheel dr


The front axle connects 4wd by vacuum. check the vacuum hoses that run to the actuator. Pay close attention to the vacuum hoses running underneath the battery as battery acid can eat thru those hose easily. Good Luck.

Dec 27, 2009 | 1987 Jeep Wrangler

1 Answer

1991 jeep 4wd fuse


Check transfer case wiring, possible loose wiring/open circuit. If your other lights in dashboard work such brake light, seat belt lights, engine light than it is not a fuse. raise all for tires from the ground and engage the four wheel drive remember to have in neutral and put in gear either 4L or 4H and see if the wheels in front move.

Apr 04, 2009 | 1991 Jeep Wrangler

1 Answer

1987 Jeep YJ [Wrangler] so owner ship says''


Our Jeep Wrangler YJ's are equipped with a vacuum module on the front axle. It is used to engage the front axle when the transfercase is shifted into 4WD. Check the vacuum lines on the front axle to make sure they are connected. The passenger side axle shaft has a disconnect sleeve that is moved left and right by the vacuum.

Mar 01, 2009 | 1987 Jeep Wrangler

1 Answer

91 wrangler 4 wheel will not engage


Check your fluid levels, you need to verify that the transfer case has fluid in it. Also, on one of my old jeeps the lever that put it into 4 wheel drive just stuck a litle. After yanking the **** out of it and moving it back and forth, drive a litle then stop and do it all over again.. a few times. it went into 4 wheel drive. this is why you are suposed to engage your 4 wheel drive once a month and drive around the block, just to make sure it gets flid where its supose to. if it doesn't get engaged then the fluid just sits at the bottum of the transfer case and doesn't get up on the gears.

Dec 20, 2008 | 1991 Jeep Wrangler

1 Answer

Jeep YJ 1991 4 wheel drive


if u got automatic front hubs stop put in park pull 4x4 shifter into 4 wheel
manual hubs at front wheels turn the hub locks to the lock position and then pull the 4 wheel shifter inti 4 wheel
also look over drivers sun visor if the tag aint worn off the direction are there... have fun 4 wheeling and keep the rubber side down
rank, rate & vote for my solution

Dec 20, 2008 | 1991 Jeep Wrangler

1 Answer

Front wheel will not engage for 4 wheel drive


very possible. Put your jeep on 4 jackstands and put in 4 wheel drive. if the front drive shaft turns pull the vacuum disconnect and check the shift fork. They usually break before the shift actuator.

Jun 28, 2008 | 1992 Jeep Wrangler

Not finding what you are looking for?
1991 Jeep Wrangler Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...