Question about 1998 Jeep Cherokee

1 Answer

Auto start will start car then turn car off 3 or 4 sec later.

The auto start that is factory installed will start the 1998 jeep grand cherokee with 4.0 motor but then 3 or 4 seconds later the motor shuts down. it does this three or four times then resets the alarm.

Posted by on

  • ruger0312 Jan 03, 2009

    thank you arsonist it was the wire to the injector for the auto start. thanks so much for your help

  • Barry May 11, 2010

    the security bypass on the remote starter may be malfunctioning

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

On most remote start application a wire is installed in motor with one wire on the fuel injectors that wire reads rpm if its to high it stalls if to low stall so check wire get back to me

Posted on Dec 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Auto start quit working, 2008 grand Cherokee, kept loosing distance, would only work sitting in jeep, now quit altogether ! All other functions work ok ! Replaced remote battery, no help !


factory installed remote ENGINE start option.??
my 2005 to 2010 service manual shows no such device.
Flashlogic, after market bs? that?
or this (later it was an upgrade) per below.
http://www.wkjeeps.com/wk_remote_start.htm
so, does car start, key in ignition? that be like first.!!
does it?
if yes, then next is to look at the cluster for evics display errors.
better is to scan to pcm and see why,
if the magic is broken, scan it, or get it scanned.
on factory cars the remote start is very strict,
and it will tell you why it fails.
is that Another key , real, came with and worked before.
the keys must be married to the PCM./BCM for them to work.
scan it

find the guy who installed it and get them to make it work.
we cant guess what is installed in your car
find a live human that can look and see that, see first if
it is factory kit or aftermarket
they do not work the same, so.......

Dec 15, 2016 | 2008 Jeep Grand Cherokee

1 Answer

My 1999 Jeep Grand Cherokee wont start due to the


you can try resetting it by disconnecting battery ,wait 30 sec then reconnect two things make sure you have drivers side window all the way down and the keys in your hand it may set off auto locks (I have seen it happen)once you reconnect battery alarm will go off and lights will flash at this point put key in drivers side door and turn it to open close 3 times with out opening door that should do it.

Sep 30, 2014 | 1999 Jeep Grand Cherokee

1 Answer

1996 jeep grand cherokee loredo V8 auto starts and drives short time later it stalls in no real pattern. fires right back up. sometimes you can hear the fuel pump and it starts fine, other...


it's in your auto start system. mine does the same thing. after it sets fot 5 mins. it starts. if it is a factory installed auto-start, have dealer check. if it was installed by someone else, theirs a problem with installation or wired wrong.

Oct 16, 2010 | 1996 Jeep Grand Cherokee

1 Answer

I have a 97 jeep grand cherokee with a 5.2 start then dies 2 sec later the relay is clicking so i tried swithing the relay still same problem and still clicks i think it may be a fuel pump ?


Your fuel filter could be plugged so only small amounts 2 seconds worth get through if ti been 3 - 5 year since it was changed now would be good.

Jan 01, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Need fuse diagram from 1998 Jeep Grand Cherokee. Don't have owner's manual. The fuse box under hood has words on it, but not the one inside on passenger's side near floorboard


Check several documents about this:

1. 1998 | JEEP | GRAND CHEROKEE Go to
- User: greatfalls / Pass: publiclibrary
- Select Auto Repair Reference Center>> 1998>> Jeep>> Grand Cherokee>> Model
- Repair Procedures
- Chassis Electrical>> Circuit Protection

2. Engine Fuses

3. ZJ-Secc-8W-Wiring-Diagrams

Good luck!!!


Jul 19, 2009 | 1998 Jeep Grand Cherokee

3 Answers

1998 jeep grand cherokee will not start


Try resetting the asd "auto shut down fuse had a similar problem the jeep would crank but did not get spark or gas also check your fuel pump? and the asd relay may be bad it will prevent the jeep from getting no spark and will not fire some jeeps have security problems

Jun 25, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Reset security


pull the battery terminals off the battery and hold the pos and neg cables together for 3-5 min. this should reset the cars computer and alarm
provided it is factory alarm...

May 03, 2009 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
1998 Jeep Cherokee Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...