Question about 1997 Mazda MX-6

2 Answers

Replacing hydraulic master cylinder in a 1997 mazda protege

I've got it loosened from under thehood but how am I suppose to get it from the inside?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 84 Answers

I hope your not a big man, go to where the pedal is remove the under dash (if it is still there) with a flashlight follow the clutch pedal to the actuator rod, 2 types of fixing. 1 remove the clip and pin, master cylinder will now clear the bulkhead. 2. remove nut and bolt. the rest as type 1. good luck.

Posted on Dec 27, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 405 Answers

There is nothing to loosen on the inside, just the lines and bolts on the outside. It just has a rod that fits between it and the pedal.

Posted on Dec 27, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My mazda protege 1997 have a hard clutch to push,is there any solution to make more smooth to push the pedal?


If you have a cable operated clutch then replace the cable as it is binding up inside the case. If you have a hydraulic clutch system the replace the clutch slave cylinder and master cylinder as there is a problem with the rubbers in the units that have expanded from contaminants and are seizing up in the cylinders.

May 26, 2014 | 1997 Mazda Protege

2 Answers

I have a 1993 Mazda Protege it is really hard to put in any of the gears while the engine is running but while engine is off it goes in all gears fine what would be the best quickest fix should I change...


Try bleeding first. The bleed port is at the right of the pic below. Here is the procedure: HYDRAULIC SYSTEM BLEEDING

  1. Remove the rubber cap from the bleeder screw on the release cylinder.
  2. Place a bleeder tube over the end of the bleeder screw.
  3. Submerge the other end of the tube in a jar half filled with hydraulic brake fluid.
  4. Slowly pump the clutch pedal fully and allow it to return slowly, several times.
  5. While pressing the clutch pedal to the floor, loosen the bleeder screw until the fluid starts to run out. Then close the bleeder screw. Keep repeating this Step, while watching the hydraulic fluid in the jar. As soon as the air bubbles disappear, close the bleeder screw.
  6. During the bleeding procedure the reservoir must be kept at least 3 / 4 full.

0996b43f80220f50-cuc0wv5q552isopkhsunrpmi-3-0.gif

Jul 02, 2017 | Cars & Trucks

1 Answer

Clutch bleeding


loosen the line at the master cylinder to allow the master cylinder to prim properly then bleed out the system. There is still air in the system.

Dec 31, 2013 | Saturn Cars & Trucks

1 Answer

I have a 2003 protege dx.I had no problems till today I pepressed the clutch pedal and it went to floor and did not come up.After looking under hood I could see where a hydraulic hose on lower driver side...


U have a broken hose, replace the hose . Take the broken hose to a parts dealer. Refill the master cylinder that powers the hose,with the proper fluid. One end of the hose will screw into master cylinder.

Sep 21, 2011 | Mazda Protege Cars & Trucks

1 Answer

I refilled my master cylinder wit break fluid and check it 5 minutes later and it was all gone, where could it gone and why?


It is either leaking in to the brake booster or at the brakes on the wheels through a caliper or wheel cylinder. Look for visual leaks under your vehicle and on the insides of your tires.

Aug 03, 2011 | 1995 Mazda Protege

3 Answers

I was told the clutch on my 2003 mazda protege is hydrolic....how do I go about adjusting it


The whole idea behind the Hydralic Clutch is there is no adjustment.If the clutch is slipping then you need a new one.If you are having trouble getting it into gear then you may have a bad clutch master and or slave cylinder.Let me know if i can help.

Feb 06, 2011 | Mazda Protege Cars & Trucks

1 Answer

How to replace the serpentine belt of protege 5 2002, also need the routing diagram


Posted by Asker under 1997 Mazda Protege for their 2002 Mazda Protege 5.
Both are included Below

Click on the following free direct Link. It has the Belt Diagrams for the 1997 Mazda Protege with either the 1.5L DOHC In-Line 4-Cylinder or 1.8L DOHC In-Line 4-Cylinder Engines; along with various engine options (AC/No AC, etc.). Included are Instrucional Diagrams for loosening (for removal) and tightening (for replacement) using the Adjustment and Locking Bolts/Nuts.
http://www.2carpros.com/car_repair_information/year/1997/make/mazda/model/protege/1997_mazda_protege_drive_belt_routing_diagram.htm

Click on the following free direct Link. It has the Belt Diagrams for your 2002 Mazda Protege 5 2.0L DOHC In-Line 4-Cylinder Engine; along with various engine options (AC/No AC, etc.). Included are Instructional Diagrams for loosening (for removal) and tightening (for replacement) using the Adjustment and Locking Bolts/Nuts.
http://www.2carpros.com/car_repair_information/year/2002/make/mazda/model/protege5/2002_mazda_protege5_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Apr 13, 2009 | 1997 Mazda Protege

3 Answers

I have a 1993 Mazda Protege. My clutch suddenly


check the line from the reservoir to the transmission for leaks, unfortunately its most likely the slave cylinder in the bell housing. Look under the bell housing of the transmission for any brake fluid at the weep hole as that would be your indicator of the slave cylinder leaking.

Nov 02, 2017 | 1993 Mazda Protege

Not finding what you are looking for?
1997 Mazda MX-6 Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...