Question about 1995 Jeep Grand Cherokee

1 Answer

How do I replace the parking light bulb?

My problem is, I can't get the outer casing of the front parking light to come off so I can get to the bulb. I tried prying on it a bit, but I didn't want to break it. I took the front grill off, thinking that there might be some screws I could take loose to eventually get to it, but I found none. Does someone know how to get the thing off to replace the bulb?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,036 Answers

I'm not sure on this model, but most are held in from within the engine bay with clips.
Undo the clips, remove the light unit a little way, and replace the bulb from behind it.
You may be able to access the bulb holder directly from within the engine bay.

Posted on Dec 26, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

4 Answers

2000 Chevy Silverado parking lights stay on. Will not shut off

Are all parking lights on or just front daytime running lights only? Either case sounds like a light control module in your fuse panel stuck.

Jul 20, 2014 | 2000 Chevrolet Silverado

1 Answer

01 jetta tdi , lower tail light sockets have room for 2 bulbs on each side , the inner ones light up in reverse but the outer bulbs do not light when other do like parking , stop , 4ways and so on = can...

The outer bulbs may not be used in your vehicle's application. Sometimes VW's and other European vehicles are equipped with rear lights that are used in foggy weather. They will come on when the fog lamps are activated and the switch on the dash will give the driver the option to turn on the right one or the left one depending on whether you are in a country that has left hand driving or right hand driving. The lights are there for "parking purposes" so that the vehicle can be seen in extreme fog conditions when parked on the street. If the vehicle isn't equipped with the system, the taillights may have provisions for it anyway.

Jan 31, 2013 | Volkswagen Jetta Cars & Trucks

1 Answer

How do I change the front side marker light bulbs?

Bi-Xenons - 6000K D1S
High Beams - Osram Nightbreakers H7
Fogs - PIAA H11 Yellow Ion
Cornering Lights - Osram Nightbreakers H3
Front Park Lights - High-Powered LEDs with built-in resistors
Front Signal Lights - Sylvania Silverstar 7507A ST (Silver Bluish but lights up Amber)
Front Sidemarkers - InviSilver W5W (Silver but lights up Amber)
Rear Signal Lights - P21W Stealth Bulbs (Silver but lights up Amber)
Reverse Lights - Sylvania Silverstar 7506ST or Error-Free LEDs
License Plate Lights - C5W Error-Free High-Powered LEDs
  • Turn the engine off and approach the side of the porsch with the burn-out side-marker light. If you are replacing both, start at either side; the replacement procedure is the same.
  • 2 Remove the screws from the plastic fender liner. Peel back the liner to access the area behind the fender.
  • 3 Reach your hand inside to gain access to the side-marker light's backing. Push the backing forward to release the side-marker lens; it's held in place by small clips.
  • 4 Grab the lens on the outer side and turn it over to access the back. Gently turn the bulb to release it from the plastic lens.
  • 5 Pull the bulb straight out to remove it from the electrical socket. Insert a new bulb, but do not touch the glass part of the bulb with your hand.
  • 6 Push the new bulb into the side-marker lens. Turn it clockwise to install it. Push the side-marker lens back into place. Apply gentle pressure to the lens to pop it back into its mount.
  • 7 Replace the screws along the edge of the fender liner.

  • Dec 04, 2010 | 2006 Porsche Cayenne

    1 Answer

    How do i change the brake light on jeep liberty 2006?

    1) You will need to open the rear swing door.

    2) On the inside jam there are two torx headed screws (T-15's if I remember correctly).

    3) Unscrew the two torx screws.

    4) The light is now held by two mounting tabs (small spherical headed plastic sets that go through a rubber grommet).

    5) You will need to pry the light casing off (easy pressure with a good size flat head screw driver will do the trick).

    6) The light bulbs are twist mount settings inside the light casing.

    7) Twist out the mount setting, change the bulbs, and reset the light mountings.

    8) To put the light casing push the light casing back on and put in the screws. Everything else will work in reverse when it comes to assembling the whole unit.

    2006 Jeep Liberty Replacement Light Bulb Sizes
    Low Beam Headlamp Bulb Size: 9007
    High Beam Headlamp Bulb Size: 9007
    Parking Light Bulb Size: 2825 or 3157
    Front Turn Signal Light Bulb Size: 3157
    Rear Turn Signal Light Bulb Size: 3757ALL
    Tail Light Bulb Size: 3157
    Stop Light Bulb Size: 3157
    High Mount Stop Light Bulb Size: 921
    Fog/Driving Light Bulb Size: 9145 or H3-55W
    License Plate Light Bulb Size: 168
    Back Up Light Bulb Size: 3157
    Front Side Marker Light Bulb Size: 168
    Ash Tray Light Bulb Size: 161
    Map Light Bulb Size: 578
    Dome Light Bulb Size: 578
    Step/Courtesy Light Bulb Size: 906
    Trunk/Cargo Area Light Bulb Size: 578

    Thank you for using fixya, and good luck

    May 08, 2010 | 2006 Jeep Liberty

    1 Answer

    I am trying to replace the front parking light bulb.

    you will have to remove the headlamp to get to the bulb.

    Jan 08, 2010 | 2002 Buick LeSabre

    1 Answer

    Today i changed the front indicators from orange to white on my front bumper of my 300c and they dont blink when indicators are on but come on and stay on when full headlights are on what have i donr wrong...

    It sounds like it's the front parking lights that are coming on. Try turning on your parking lights only(first click or first position of your light switch) and see if the lights you replaced are on. If this is the case, check to see if you replaced the bulbs with same function number as originals, Or possibly there are another set of bulbs for the directional signals.

    Aug 16, 2009 | Chrysler 300C Cars & Trucks

    1 Answer

    I have a left front clearance light out how do you get it out 1

    Signal and Marker Lights REMOVAL & INSTALLATION Front Turn Signal and Parking Lights
    1. Disconnect the negative battery cable.
    2. At the rear of the front bumper, turn the bulb socket 1⁄4 turn and remove the socket from the parking brake housing.
    3. Remove the bulb from the socket; if necessary, replace the bulb.
    4. If lens replacement is necessary, remove the retaining bolts and remove the lens from the bumper.
    5. To install, reverse the removal procedures. Check the turn signal/parking light operations.
    Fig. 1: Common front turn signal/parking light mounting

    Fig. 2: Twist and remove the bulb socket from the back of the turn signal/parking light lens

    Fig. 3: If lens removal is necessary, loosen and remove the retaining bolts


    Jul 24, 2009 | 1992 GMC Sonoma

    3 Answers

    Replace parking/marker bulb front pass 98 Jeep Grand Cherokee

    look in between the marker and headlights its a screw there screw it out

    Apr 04, 2009 | 1998 Jeep Grand Cherokee

    4 Answers

    How do i replace the parking light bulb on a 2004 saab 9-3 please

    I replaced my parking light bulb in about a minute. You just have to pull the cables. Believe me, this is the procedure stated in my SAAB repair manual. Those cables are reinforced, don't worry. To tell the truth a would have not done that if I hadn't seen it in the manual . Contact me and I can send you the diagram with the step by step directions.

    Oct 16, 2008 | 2004 Saab 9-3

    1 Answer

    How do I change my front park light bulbs ?

    You only need to unscrew the vertical bolt located at the upper-outer side of the headlight, then you only have to pull the park light screen to the front of the vehicle -it could be a litlle hard-, the rest is only turning the bulb socket and take it out. To mount it the opposite procedure.

    For additional information I would need your e-mail.

    Jun 27, 2008 | 1995 Toyota Corolla

    Not finding what you are looking for?
    1995 Jeep Grand Cherokee Logo

    Related Topics:

    77 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts


    Level 3 Expert

    71525 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22059 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7029 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides