Question about 1993 Ford Crown Victoria

1 Answer

When you press the brake pedal it will go all the way to the floor...

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 334 Answers

Check brake fluid

Posted on Dec 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

BRAKES BLED PEDAL GOES TO FLOOR WHEN STARTED


if a master cylinder is bad and you are sure you have all the air out and no leaks.pedal will go to floor , running or not. if booster is bad it will cause a hard pedal. but if master cylinder is bad it will turn on a brake light on dash if it works. make sure the wheel cylinders are not leaking. I beleive that the master cylinder is bad, or you have a leak somewhere. If the master cylinder is functioning properly, the brake pedal will depress to a certain depth and no further.

Apr 20, 2012 | 2000 Chevrolet Blazer

1 Answer

How do i bleed new brake caliper


Press brake, let off. Open bleed screw until the fluid runs out with no bubbles. Tighten bleed screw. Press brake and hold. Open bleed screw until pedal goes to floor then close bleed screw with pedal pressed to floor.. Fluid should come out with no air bubbles when open. If they are present repeat the last part.

Jan 16, 2011 | 1996 Lexus ES 300

1 Answer

Brake pedal is sometimes sinking to floor. Brake


most likely your master cylinder is acting up try to press hard on your break for a period of time and see if the pedal will sink/replace master

Jan 13, 2010 | 1993 Toyota Pickup

2 Answers

How do I bleed air from the brakes


Two persons are required: one to bleed and other to press brake pedal.
Remove wheel and hub of the side you want to bleed. You will find the bleed nut there. Open it a little until some oil flows out. Ask the other person to press brake pedal with steady pushing and withdrawing until he feels its tight while you slowly tighten the nut. Adjust tightness of pedal by trial. Don't forge to refill the brake fluid after bleeding all the brakes.

Do give my solution the highest rating if it solves your problem. Thank you for using fixya!

Aug 07, 2009 | 1989 Volvo 240

1 Answer

Brake pedal will go all the way to the floor


make sure brake fluid is full. then pump brakes for one minuite check the fluid to see if it went down or stayed full. if it went down then check the system for a leak . if it stays full then you will need a new mastercylender . i dont think you have a vacum problem cause this causes a verry stiff brake pedal not one that goes to the floor

Dec 26, 2008 | 1993 Ford Crown Victoria

2 Answers

Soft brake pedal after rotor replacement


If they rebled the brakes and the pedal goes to the floor, chances are that the master cylinder is bad. Probably cost about $80-100 for the part if you could do it yourself

Nov 30, 2008 | 2003 Acura 3.2CL

1 Answer

Excessive brake pedal travel and 'soft' brakes


the brakes have to be bleed you wrote that when you start the car the pedal goes to the floor that means the booster is working fine take it back and tell them you want the brakes bleed

Nov 14, 2008 | 2003 Honda Accord

2 Answers

Brakes


sound like you need a master cylinder

Jul 31, 2008 | 1989 Ford F 350

Not finding what you are looking for?
1993 Ford Crown Victoria Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63572 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...