Question about 1996 Chrysler Sebring

1 Answer

I want to replace the thermostat in my 1996 Chrysler Sebring on my own, is this possible?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 405 Answers

Easy job, drain coolant down some with drain **** on bottom of radiator, follow upper radiator hose to where it connects to engine. Remove the housing the hose is connected to, remove old thermostat, being sure to notice which way it goes in, clean old gasket serfaces, intall new thermostat in the right direction install new gasket tighten securely and top of the coolant you drained.

Posted on Dec 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sebring thermostat


I vaguely recall a bleeder on the intake or close to the top? Trapped air will make it overheat again.

Apr 02, 2014 | 2002 Chrysler Sebring

1 Answer

Need wirings diagram for 1996 Chrysler Sebring (FJ-110A) and (FJ-111A)


You may have to get a repair manual for your Sebring to see those diagrams.
However, here's a possibility: Go to www.autozone.com and register there-it's free. It will ask you what car you have, year and so on. After you are registered, you can see what they have to offer for diagrams. It's not complete, but they have about 20 pages of wiring diagrams on Chrysler products, including Sebring.
Good luck.

Dec 05, 2011 | Chrysler Cars & Trucks

1 Answer

No heat in chrysler sebring


Thermostat is bad or heater core needs flushed out.

Feb 02, 2011 | 1996 Chrysler Sebring

2 Answers

2001 chrysler sebring leaking water beneath thermostat housing through a factory hole , I changed thermostat and gasket no change


Hi,

This is called the water pump weep passage which is a sign that your seal in the water pump has failed.

You need to replace the water pump.

Sep 15, 2010 | 2001 Chrysler Sebring

1 Answer

Where is the starter located on a 1998 chrysler sebring coupe


Follow the +cable from the battery. The starter is on the other end.

Oct 21, 2009 | 1996 Chrysler Sebring

1 Answer

Termostat how to repair


one rad hose goes to the water pump the other goes to the thermostat on top of the motor. undo the hose clamp and take off the hose that goes to the thermo . DO THIS WHEN THE VEHICLE IS COLD. have a small container handy to catch any coolant that may leak out. be sure to keep the hose up so coolant doesnt leak all over the ground.Once you take off the hose the thermostat should be right there. 2 bolts to take it out. fairly simple actually. replace with the new one and put hose back on. replace any coolant that might have leaked into your container. Hope this helps you Crystal. let me know. Thanks, Mark.

Sep 21, 2008 | 1996 Chrysler Sebring

1 Answer

Replacing headlight in 1996 Chrysler Sebring JXI


piece of cake....
take off the two "star" bolts, one toward the center of the engine above the light assembly and the other toward the fender (it is very long). when you remove them both the entier assembly falls off into your hands and makes changing the bulbs much easier.

Aug 25, 2008 | 1996 Chrysler Sebring

Not finding what you are looking for?
1996 Chrysler Sebring Logo

Related Topics:

363 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...