Question about Toyota Camry

1 Answer

Where is the blower motor resistor in a 1999 mazda protege

Blower worked when I hooked it up 2 a battery charger. it only worked on high until the other night, now nothing at all

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 405 Answers

Follow wire from your blower to the resister. it should be mounted in the duct near the blower with a couple of screws. Also check yourfuse if you haven't.

Posted on Dec 26, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Blower motor not working on 4 1998 Mazda protege

check for power and ground at the blower motor. if this is good then hit motor. if it starts the motor needs replacing. then check the fuse then the fan speed switch for power and ground going to the switch and coming out of switch.

Jul 28, 2015 | 1998 Mazda Protege

1 Answer

Is there a blower motor relay or fuse on a 1995 Mazda Protege lx?

That fuse sounds like it powers the ac compressor.
The blower motor usually takes a 30 amp fuse.
Does the blower motor work if you hook it to direct voltage ?

Jul 04, 2012 | Cars & Trucks

1 Answer

The fan motor on my 2001 Mazda Protege only works on high. I do not know if it is the switch or the motor. I have read also that there may be a resistor involved. Where do I start?

If you have access to a multimeter and know how to use it then you can unplug the resistor plug and check the is usually located on the blower housing as it uses the air from the blower to keep it cool...the resistance reading will be very low...if any one shows an open condition(no reading) then you will need to replace the resistor...if you don't have a multimeter, you can try to change the resistor as they usually are not that expensive...the switch does not go bad that often

Dec 21, 2010 | 2001 Mazda Protege

1 Answer

Where can i find the blower motor resistor on a 97 mazda protege?

I think any parts store can get it for you.

But if you asking for location of the component , then it's a different story.
All b/m resistors(any car) located around blower motor or in the air duct after blower motor, they need to be vented all the time , otherwise they overheat and blow. Wires from motor are going to resistor , so if you trace the wires you'll find resistor.

May 05, 2010 | 1997 Mazda Protege

1 Answer

Heater fan only works on high?

100%: Blower Motor Resistor needs to be replaced. It is located adjecnt to the Blower Motor.

Jan 28, 2010 | 2002 Mazda Protege

2 Answers

Where is the blower motor resistor on a 2002 mazda protege?

just remove the glove box and its right behind it just take the white pug out and the two phillips screws to remove the resistor out, replace with the new one and cool off!!!! Hope this helps

Jan 31, 2009 | 2002 Mazda Protege

2 Answers

Blower motor & resistor on 1999 mazda protege. It worked only on high for the last few months. Which would be the resistor. It stopped working totally the other day, I messed around with it and got to work...

just change the resistor b/c when resistor go bad they get stuck on high or low. selecting on low give you more resistor and less flow of air from the blower and on high side you get less resistor and more flow

good luck

Dec 29, 2008 | 1993 Mazda Protege

1 Answer

Air conditioner

If the blower is not working at all it could be the blower or fuse or switch but if it blows on high only it could be your blower motor resistor.

Aug 27, 2008 | 1998 Mazda Protege

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

82208 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides