Question about 2000 Chevrolet Venture

1 Answer

2000 ventures timing chain failed does it bend valves?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 318 Answers

I think this is an interference head,,so yes a valve could be bent.
do not try to start this engine with the starter motor,,if you want to check for damage, take all of the spark plugs out, and then turn the engine over by hand, if it stops and feels like its coming up against an obstruction, this will probably be the valve.
Sometimes its just easier to remove the cylinder head and inspect the valves and pistons then.

Posted on Jan 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 saturn ls time chain replacement


What exactly do you need to know about replacing the timing chain? Also you should note that the L200 (4 cyl) has a timing chain. The L300 (V-6) has a timing belt.

Another thing to note is that both of these are interference engines. If your timing chain (or belt) has failed and the engine will not start, the valves are likely bent and you may have damaged the pistons as well.

Mar 01, 2015 | 2000 Saturn L-Series

1 Answer

My 4.7ltr has low compression in cylinder


if its one cylinder then it could be piston damage, valve damage, camshaft lobe damage for this cylinder, rocker has come off. if its on all cylinders it could be a jumped timing chain caused by something damaged in the timing chain components which could possibly bend the valves.

Aug 30, 2014 | 2000 Jeep Grand Cherokee

1 Answer

What does the car do when the timing belt goes out


The 2001 Cavalier does not have a timing belt....it has a chain. That being said, the tensioner for the timing chain is a common failure item. If the tensioner fails while the car is at speed, the timing chain will jump across the crankshaft teeth, putting the crankshaft and camshaft out of synchronization. This will cause the car to immediately shutdown, the pistons in the engine will come up and hit and bend the valves, resulting in internal damage to the engine.

Feb 14, 2014 | 2001 Chevrolet Cavalier

1 Answer

Just got a 2000 s type with timing chains removed. it is a 4.0 with 93k. are timing chains com. to go? also what could a back yard mac. do to really mess this engine up, seller said it could have bus


i think they bend valves when they blow the chain not only that they would have fixed it blow air into the cylinders and see if air blows out

Aug 20, 2012 | 2000 Jaguar S-Type

1 Answer

I just wanted to know if this model has a timing belt or timing chain.


Timing belt on this vehicle. Replace at 120K miles. You may bend a valve if the belt breaks on you. Very expensive then.

Aug 30, 2011 | 2000 Hyundai Accent

3 Answers

Is it a timing belt on olds intrigue 2000, 3,5L?


this engine uses a timing chain, chains require no replacement unless the engine is being repaired or the chain or spockets fail

Mar 26, 2010 | 2000 Oldsmobile Intrigue

1 Answer

2oo2 cavalier timing chain broke need to know how to fix it??


With a new motor most likley. When a timing chains break pistons tend to collide with valves which can punch holes in the pistons or bend/ break valves. Usually at this point it is more economical to replace the engine than to actually fix it.

Jan 20, 2010 | 2000 Chevrolet Cavalier

2 Answers

Why are exhaust valves bending on 97 s-10 blazer. The valves are not sticking. Could I have a timing chain issue? Hard to believe because the motor runs so good until the valves bend. You can see the mark...


bent valves can be from timing belt stretch but would have been running very rough and would have had to be replaced others are bad valve springs- rocker arms not adjusted right- valve sticking-push rods sticking-camshaft walking- oil pressure problems

Jan 16, 2010 | 2000 Chevrolet Blazer

1 Answer

2000 ford 4.0 sohc how to set feront timing chains chain stops broke off now cannot reset no timing marks


you kinda destroyed it. you need specialty tools, a good manual, and new parts. You don't do this right the first time, you bend valves, period.

Oct 27, 2009 | 2000 Ford Explorer

1 Answer

Timing Chain


stop running it untill you get the chain fixed you will know when it breaks or slips as the motor will not run at all and will bend the valves this will require the motor to come apart and basicley be rebuilt -jeff

Sep 02, 2008 | 2000 Jaguar S-Type

Not finding what you are looking for?
2000 Chevrolet Venture Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...