Question about 2003 Mitsubishi Lancer

1 Answer

WHERE IS THE CAMSHAFT POSITION SENSOR ON A MITSUBISHI LANCER ES

ENGINE 2.0

Posted by on

  • Anonymous Apr 12, 2009

    how can i find the camshaft sensor

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

It is right underneath your air cleaner.

Posted on Jan 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing marks for an 03 mitsubishi lancer


the marks on the cam shafts are directly vertical at the top in line with a mark in the back of the housing the balance shaft timing mark is at 9 oclock position
the crank shaft timing mark is at 10 oclock position ( lining up with a pointer) and the oil pump mark is also at the 10 oc;ock position lining up with a pointer
( to check the position of the oil pump sprocket remove a plug -shown in the book -and insert .30dia pointed screw driver (5/16 philips ) to at least 2.4 "
if it cannot be inserted to this depth move the oil pump sprocket until it can)
the process of assembly is -:
install the timing belt to the sprockets and pulleys in the following order , retaining the belt to the camshaft sprockets by the use of suitable binding clips ( clothes pegs etc)
crankshaft sprocket
oil pump sprocket
guide pulley
exhaust camshaft sprocket
intake camshaft sprocket
tension pulley
to help install the belt the auto tensioner on the lh side should be removed
all of this information will be included in a workshop manual covering lancer engines for the years listed and will also include all tensions for the bolts --If you do not have the workshop manual then it is STRONGLY recommended that you obtain one
information from autodata belt installation manual lancer 2.0 l
2003-2007 engines

Oct 17, 2015 | 2003 Mitsubishi Lancer

1 Answer

Mitsubishi lancer check engine light


yeah, if I were you, I will erase the fault code with your OBD2 car code scanner first. If the engine light on, there must have some questions on the throttle position sensor, I will fix it.

Dec 10, 2012 | 2008 Mitsubishi Lancer

1 Answer

How to replace crankshaft position sensor in 2004 mitsubishi lancer es 2.0


It's attached to the timing belt cover u have to remove ac and harmonic balance pulley and the motor mount and the alternator it's no small job so if ur not a mechanic .... GET ONE!!!!

Jan 29, 2012 | 2004 Mitsubishi Lancer

1 Answer

I got a p0340 troubleshooting code on my 2002 mitsubishi lancer. how dependable are the readings?


P0340--is the Camshaft Position Sensor Circuit.

These readings are very accurate..


Jul 23, 2011 | 2002 Mitsubishi Lancer

2 Answers

Torque settings for 2005 lancer es fly wheel gearbox etc


2.0L Evolution engine

flywheel bolts 132 =/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.0L Non- Evolution engine

flywheel bolts 98 +/-5 N.m. 72 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.4L Ralliart engine

flywheel bolts 132 +/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

Dec 28, 2010 | 2005 Mitsubishi Lancer

2 Answers

P0345 Code, where is camshaft position sensor "A" (bank 2)


The Camshaft Position Sensor (CMP) on the 4.0L 6cylinder engine is bolted to the top of the oil pump drive shaft assembly. The sensor and drive shaft assembly is located on the right side of the engine near the oil filter.

a4b74c1.jpg

Fig. 1: Component locations-ES300

a7bce64.jpg

Fig. 2: Component locations-ES300



Hope this help; remember comment and rated this. TY for using Fixya.



May 06, 2010 | 2002 Lexus ES 300

1 Answer

Trouble code is gen fr.


it's your alternator (64)
1 Engine control module malfunction
11 O2 sensor malfunction (Car usually runs weak when this code appears) (If a V6 this relates to the O2 sensor on the drivers side In a 4x4 Or the one at the back of the engine on a Galant)
12 Mass air flow sensor circuit malfinction
13 Intake air temperature sensor (Comes on if you have chucked the sensor away to fit some big fancy K&N induction kit!)
14 Throttle position sensor fault
21 Engine temp sensor malfunction (Check the spark plugs too because they carbon up if this sensor is causing the car to run rich)
22 Crankshaft position sensor (Try cleaning the dirt off the end before replacing)
23 Camshaft position/distributor hall sensor (Common on Galant 1800)
24 Vehicle speed sensor
25 Barometric pressure sensor (Another name for the MAP sensor)
31 Knock sensor circuit
36 Ignition timing adjustment connector fault
41 Injectors circuit malfunction
44 Ignition coil/ignition amplifier cylinders 1 and 4
52 As above for 2 and 5 (on a V6)
53 As above for 3 and 6 (On a V6 too)
54 Immobiliser control module to engine control module malfunction (comes on if you have changed one or the other and not had them programmed in by Mitsi)
55 Idle speed control actuator malfunction (A good injector cleaner and a thrash up the motorway usually fixes this!)
59 O2 sensor (if you have a V6 this is the sensor on the passenger side ona 4x4 and the one at the front on a Galant etc.)
61 Transmission control module/engine control malfunction
62 Intake manifold air control actuator/position sensor malfunction
64 Alternator malfunction (remember to check under load and when revved up)
71 Traction control vacuum solenoid malfunction (check the pipes for leaks)
72 Traction control vent solenoid malfunction (usually blocked with dirt)

May 13, 2009 | 2002 Mitsubishi Lancer

1 Answer

Camshaft position sensor


The camshaft position sensor is usually located on the cylinder head near the camshaft. It may be under the timing cover. It has a small plug and the sensor is where the plug is plugged on.

Jan 23, 2009 | 2003 Mitsubishi Lancer

1 Answer

Engine turns but won't start


No.: TSB-07-11-001
DATE: January, 2007
MODEL: 2002-07 Lancer 2.0L
SUBJECT:
HARD TO START ENGINE DTC P0340 (and P0335)

PURPOSE
The engine may be hard or impossible to start and MFI DTC P0335 and possibly P0340 may be stored due to abnormal wear to the camshaft position sensor support. Oil grooves have been added to the camshaft position sensor support to improve lubrication

Nov 04, 2008 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
2003 Mitsubishi Lancer Logo

Related Topics:

999 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...