Question about 2006 Toyota Tundra

1 Answer

06 tundra remote

How can i program my keyless remote in my 06 tundra #fcc id hvq12bbx ,,ic:1551a-12bbx

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Http://www.programyourremote.com/classified/DisplayAd.asp?id=1303

check out this website. I had to reprogram mine too. Good Luck!

Posted on Mar 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Toyota Tundra can't key a new keyless entry dealer says it could be two different systems


A blown motor wouldn't have anything to do with programming a remote. Most locksmiths can do this as well.

Jul 20, 2016 | 2002 Toyota Tundra

1 Answer

Toyota tundra keyless remote will not program


You have to go to a toyota dealer service centre to program the remote. But I am sure you are well aware of that.

Dec 21, 2012 | 2005 Toyota Tundra SR5

1 Answer

Need help programing my keyless remote for a 2000 alero. This is what is on the back, GM/UTA 25665575, FCC ID. KOBUT1BT,Canada 1983 101 393 It has four buttons top two are left pic of lock, Right pic of...


1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.



Thank you for using Fixya and good luck

Mar 17, 2010 | 2000 Oldsmobile Alero

1 Answer

Programming keyless entry key fob for 2000 chevy


you need to call the nearest chevy dealer with you vin, and get the part number from them, there are 2 numbers on the back of the remote, see if they match what the dealer tells you. Have an automotive locksmith program, should cost about 75.00 to do.

Jan 27, 2010 | 2000 Chevrolet Malibu

2 Answers

Hi. Do you what the FCC ID is for the Nissan Versa (Tiida) 2006. I am trying to purchase a new keyless remote. Thanks. RJ


I believe that with most keyless entry systems, you must buy the remote specific to Nissan Versas, and then either take it to a dealer to have them program your in-car receiver to understand the new remote signal, or download the instructions and add it yourself. FCC ID should have absolutely bearing on this.


Dec 04, 2009 | 2006 Nissan Versa

5 Answers

Purchased 2003 spyder convert with no remote ... confirmed keyless entry with mitsubishi motors but they say there are 4 remotes and to call parts at a dealership. The dealership says the only remote they...


Why not go on http://www.ebay.com?

There you will get it. I got one for my Galant and it works great.

Good luck.

But even if you pick the one available, it makes no difference. It will be programmed for your car. They are mostly universal.

Remember to rate this solution.

Aug 24, 2009 | 2003 Mitsubishi Eclipse Spyder

1 Answer

Need of programming instructions for keyless entry for 1996 LHS


System operation
System will automatically lock all doors when vehicle is driven in excess of 15 mph
Pressing UNLOCK (on remote) once deactivates system and unlocks driver door only
Pressing UNLOCK (on remote) twice w/in 5 seconds deactivates system and unlocks all doors
Alarm/central locking functions can be altered using remote transmitter


Programming

Access data link connector (DLC)- druvers sude fascia
Switch ignition on
Jump DLC terminal 1 and ground
Ensure doors lock and unlock, indicating programming mode active
Press any button of each remote to be programmed
Ensure doors lock and unlock after each remote operation - indicating programming complete
Remove jump lead to exit programmming code

A maximum of two remotes can be programmed

Jan 20, 2009 | 1997 Chrysler LHS

1 Answer

Keyless remote programming insyructions


If the remote is generic you will need the factory remote to "clone" the signal to the new remote.

With your oem pontiac remote you may need to visit any GM service center to have the remote set to the cars receiver. There are literally 100,000 different variables GM uses to ensure one remote can't work the wrong car. A typical key programming will run you between $30-$60 depending on how much greed the technician has. Some good technicians will do this job for free simply to make a customer happy so you may wish to call around.

Jun 29, 2008 | 2000 Toyota Corolla

Not finding what you are looking for?
2006 Toyota Tundra Logo

Related Topics:

349 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...