Question about 2003 GMC Yukon

Open Question

Front wheel bearings AWD yukon denali

I just repalced the front wheel bearing on my 2003 GMC yukon denali all wheel drive. Now I have a rubing,grinding noise. Is there adjustment for the front wheel bearing?

Posted by on

  • Anonymous Feb 16, 2009

    wheel bearing

×

1 Suggested Answer

  • 450 Answers

SOURCE: front wheel bearing

156 ft lbs

Posted on Mar 17, 2009


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque settings on the front wheel hub bearing assembly for a 2003 gmc yukon denali xl?


155 Ft/Lb is the correct Torque

http://www.speedwayautoparts.com/Torque%20Specks.pdf

Mar 23, 2013 | 2006 GMC Yukon Denali

2 Answers

2004 yukon denali shakes a little in the front end at speeds 45 to 50 mph..almost feels like driving on a flat tire..what could be the prob?


the front wheels may need balancing or it could be a loose or worn tie rod end or other loose component on the front end, you will need get under the vehicle & have a good look & give the steering components & anything else a good shake to see if you can see anything loose or worn.........hope this helps......cheers.

Sep 07, 2011 | 2004 GMC Sierra Denali

1 Answer

I can't Desactived the four wheel drive where is the switch for the four wheel drive, is a GMC YUKON DENALI 2007


{: ) If your vehicle has an AWD (All-Wheel Drive) feature, engine power is sent to all 4 wheels all the time. This is like four-wheel drive, but there is no separate lever or switch to engage or disengage the front axle. It is fully automatic, and adjusts ityself as needed for road conditions.

Jan 07, 2011 | 2007 GMC Yukon Denali

1 Answer

Rear wheel bearing is out, how easy to repair


not easy,you will probably need a hydraulic press to remove and reset the bearings

Apr 20, 2010 | 2002 GMC Yukon Denali

1 Answer

02 yukon denali has a whining noise similar to bad wheel bearings. wheel bearings were just replaced. could it be cv's, no clunking sound though. also, sometimes the vehicle ''jerks'' when accelerating,...


the jerking and noise you are experiencing is the drive chain and bearings in the transfer case also you may want to check the end play in both front and rear pinion bearings and yokes

Jan 22, 2010 | 2002 GMC Yukon Denali

1 Answer

Proper torque for bolts on front wheel


The axle nut spec is 177 foot lbs. and the bearing to knuckle bolts spec is 133 foot lbs.

Dec 23, 2009 | 2004 GMC Yukon

2 Answers

2004 GMC Yukon Denali Awd humming sound in front of truck


The Denali's are really susceptible to front dif. wear and failure. Because it is AWD, the front dif is always working unlike a 4WD. GM, in order to lighten up the front end built the front dif in aluminum. If it was the same as the rear, it would be bullet proof, but much heavier. After about 80,000 miles it is common to have bearings failing. Remove the drain plug which happens to be magnetic. You may see more than just the normal fine filings. You will likely see larger chunks of metal some of which is not even magnetic but will drain out with the oil. You are likely looking at a $1500 rebuild. It will get much louder and run for a long time before it really goes south.

Nov 29, 2008 | 2005 GMC Yukon Denali

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,360 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...