Question about 2000 Ford Windstar

1 Answer

STARTER GONE How to remve starter 2000 windstar

Posted by on

  • windstarfixd Dec 26, 2008

    Brand new alternator, Battery is Excellent, 3rd time having to replace the alternator tho'.



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 319 Answers

Posted on Jan 02, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How Can a fan belt tensioner malfuction keep a motor from moving ?

Can you turn the engine by hand to make sure the engine isn't seized or hydrostatic lock? If you suspect hydrostatic lock, remove the spark plugs, then see if it will crank.
I don't know if you can visually inspect that the starter drive gear is engaging the flywheel? I can't see much from here, only make suggestions.

Dec 27, 2015 | 2000 Ford Windstar

1 Answer

200 windstar with a 3.8 motor cranking very slow then stops cranking and does not start

Could have a bad cable , to check voltage drop starter circuit ! Starter Voltage Drop Watch some other voltage drop testing videos ! You need a DVOM - digital volt ohm meter to do this testing .

Dec 21, 2015 | 2000 Ford Windstar

2 Answers

1995 Chevy Z71 PU

Probably the starter has failed.

Dec 31, 2013 | 1997 Chevrolet Cavalier

1 Answer

My 2001 ford windstar will not start. lights exterior and interior turn on catr is getting electrical power but no clicking or sound when trying to crank and car will not crank

Sounds the the starter has gone out. Will have to be replaced.
Any Autozone or autoparts store will be able to look the exact starter you will need, and also offer ways to replace or show you how to replace it your self.

Mar 16, 2011 | 2001 Ford Windstar

1 Answer

How to replace starter on 2000 ford windstar

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
    NOTE When removing the hard shell connector at terminal -S-, grasp the plastic shell. Do not pull on the wire.
  3. Disconnect the starter electrical harness.
  4. Remove the upper starter bolt.
  5. Support the starter and remove the lower bolt.
  6. Remove the starter from the vehicle.

    Fig. The starter is located at the lower front of the engine, and is visible through the air duct

To install:
  1. Position the starter in the vehicle.
  2. Install the upper and lower bolts. Tighten to 15-20 ft. lbs. (20-27 Nm).
  3. Connect the starter electrical harness. Tighten the starter cable nut to 80-124 inch lbs. (9-14 Nm).
    NOTE When installing the hard shell connector, be careful to push it straight on and make sure it locks in position with a notable click or detent.
  4. Lower the vehicle.
  5. Connect the negative battery cable.

Hope helps (remember comment and rated this).

Jul 14, 2010 | 2000 Ford Windstar

1 Answer

How to install a starter on a windstar 2000

remove the neg battery terminal.
remove the positive lead from the starter.
remove the trigger lead.
remove the mounting bolts (2 in front and one behind the solinoid.

installation is the reverse of removal

Mar 08, 2010 | 2000 Ford Windstar

1 Answer

2000 ford windstar will not turn on

when u changed the ECM did you have it matched to the PCM or immobiliser ? , normally these need a Pc to reset these to the motor
you should have a small and large power lead going to the starter motor, when you turn key to crank position the small feed on starter should power up,if not check that happens at the ign switch, or it may be if your car is an auto the switch in the gear selector may have gone , or if manual the clutch pedal switch ,

Dec 05, 2009 | 2000 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides