Question about 1996 Ford Windstar

1 Answer

Ford winstar serpentine belt install

I can not get the adjuster to move,is there a lock release on it or a trick to making it move?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Use a breaker bar for leverage to release tensioner.

Posted on Dec 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install serpentine belt 1988 ford 150


Loosen the lock bolt on the upper part of the tensioner(arrowed in black). Release tension on the belt at the tensioner(arrowed in red) by turning counter clockwise on the pulley nut as indicated in blue.
Slip the belt off the pulleys while keeping pressure on the tensioner. Refit the new belt and make sure it is properly located on all the pulleys before releasing pressure on the tensioner. Tighten the lock bolt.
The tensioner is self adjusting you just need to make sure the belt is properly seated on all the pulleys before tightening the lock bolt.
The exact position of the tensioner varies on the different engines but the routing is the same and it is always between the alternator and power steering pulleys on the gas engines.
C - Cranshaft
A - AIR pump
Alt - alternator
W - Water pump
P - Power steering
A/C - airconditioning

suzman_48.jpg

Dec 02, 2010 | 1988 Ford F 150

1 Answer

2000 ford winstar 3.8l engine how to put on a serpentine belt


You need to use a wrench or serpentine belt tool to turn the belt tensioner by connecting to the pulley bolt and turning it clockwise.

Oct 07, 2010 | 2000 Ford Windstar

1 Answer

Serpentine belt broke on 87 ford econo van


ps...you do not have to Post another Question....just Add a Comment to this question.

"HOW TO": I professionally prefer the Serpentine Tensioner Tool.
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s).
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (located on the Tensioner Pulley rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley and Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.

Apr 15, 2010 | 1987 Ford Econoline

2 Answers

Install Serpentine Belt 2004 Ford Freestar


Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagram for your 2004 Ford Freestar. You either have the 3.9L or 4.2L V6 Engine. I am not sure what Engine options (AC/No AC, etc.) you have. If this Diagram is not correct: check on the underside of your Hood for the correct Belt Diagram. However the below "How To" remains accurate.

http://www.2carpros.com/car_repair_information/year/2004/make/ford/model/freestar/2004_ford_freestar_drive_belt_routing_diagram.htm

"HOW TO":
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s). (See Diagram on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Apr 03, 2010 | 2004 Ford Freestar

1 Answer

How to replace a zx2 serpentine belt


Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 1998 Ford Escort ZX2, 2.0L DOHC In-Line 4-Cylinder Engine.
The Link says 2000 for the Year, however this is the same as the 1998 Year Model.

http://www.2carpros.com/car_repair_information/year/2000/make/ford/model/zx2/2000_ford_zx2_drive_belt_routing_diagram.htm

"HOW TO":
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Apr 03, 2010 | 1998 Ford Escort

1 Answer

The crankshaft turns but won't turn the serpentine belt after radiator fluid got on it!


Remove and Replace the Serpentine Belt.
Click on the following free direct Link. It has the Serpentine Belt Diagram and Tensioner location for your 3.0L V6 including the DOHC engine.
http://www.2carpros.com/car_repair_information/year/2000/make/ford/model/taurus/2000_ford_taurus_drive_belt_routing_diagram.htm
GENERAL/Standard Rules to Removal the Serpentine Belt with a Tensioner:
A. Find the Tensioner(s). (See Diagrams on Link)
B. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
C. Remove the loosened belt off one of the other more easily accessed Pulleys.
D. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

Mar 06, 2010 | 2000 Ford Taurus

1 Answer

1999 sebring serpintine belt installation


My sincere apologies for the severly delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, however I am answering it in case you still do.

Click on the following direct Link. It has several Diagrams for your Belt depending on your engine size and options (AC/No AC etc.) AND whether you have Tensioners OR Locking/Adjusting Bolts/Nuts.
IF APPLICABLE: These point out the direction of rotation for the Tensioner in order to loosen and reinstall the Belt.

IF APPLICABLE: These also point out where the Locking and Adjusting Bolts/Nuts are, to loosen the belt and remove; and reinstall the Belt and .

Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating it\moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.


Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

http://www.2carpros.com/car_repair_information/year/1999/make/chrysler/model/sebring/1999_chrysler_sebring_drive_belt_routing_diagram.htm

Dec 28, 2009 | 1999 Chrysler Sebring

1 Answer

How to replace a serpentine belt in a ford winstars


e

b1513bf.jpg

Fig. Accessory drive belt routing-3.0L engine



21dafdb.jpg

Fig. Accessory serpentine belt routing-3.0L engine


96f660b.jpg

Fig. Accessory serpentine belt routing-3.8L engine


Removal and Installation

2928bae.jpg

Fig. Drive belt tensioner wear indicator marks


2375d13.jpg

Fig. Place a wrench on the drive belt tensioner bolt and rotate the assembly clockwise to relieve belt tension

Using a 15mm wrench attached to the drive belt tensioner pulley, rotate the tensioner clockwise to release the tension. Remove the drive belt from the pulley. When installing the new drive belt, ensure that the drive belt is routed correctly and note the position of the indicator mark on the tensioner.

Hope heled with this; remember rated this help. Good luck.

Nov 12, 2009 | 2000 Ford Windstar

1 Answer

Replace a fan belt on a 2001 Ford Winstar 3.8l engine


how to replace a serpentine belt in a ford winstar

Oct 29, 2009 | 2001 Ford Windstar

1 Answer

Need diagram for serpentine belt on 2001 ford winstar and how to release tension to install


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.

The simple rule in removing the Belt: Rotate/Move the Tensioner Pulley away from the belt and towards the "open area" AND remove the belt off from one of the other more accessible Pulleys. They have serpentine belt remover bars/tools available at most auto parts stores and Harbor Freight.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/2001/make/ford/model/windstar/2001_ford_windstar_drive_belt_routing_diagram.htm

Sep 06, 2009 | 2001 Ford Windstar

Not finding what you are looking for?
1996 Ford Windstar Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...