Question about 2001 Volvo V70

1 Answer

How do I disconnect the fwd. fuel pipe coupling (under the engine

I have to replace the fuel pipe from the outlet of the fuel filter to the push on coupling under the rear of the engine. How do I disconnect this front coupling? is a special tool needed?

Posted by on

  • zerbal Dec 26, 2008

    Thank you!!!!

    I'm on my way to the parts store now.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 409 Answers

You will need a sppring lock removal tool. Go to a parts store and ask them for the fuel line removal tool kit. There should be 5-6 pieces and it is not that expensive. The tool itself has a **** in it and a big end and a small end. You slip the tool over the metal line small end towards the lock and just push it in and pull the lines apart.

Posted on Dec 25, 2008

  • John Weathers
    John Weathers Dec 25, 2008

    The tool has a slice in it so it will fit over the metal line. LOL they sensored the first word I used in place of slice. Also the tools are white nylon so you can know you are buying the right thing.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace a fuel filter on 2001 ford expedition


Instructions

Park the vehicle in a safe place and with enough room for you to work around your Expedition.

Loosen the filler cap, open the hood and remove the accessory cover from the fuel supply manifold or fuel rail.

Remove the black, negative battery cable and relieve the fuel system pressure. Locate the Schrader valve right before the first fuel injector on the fuel rail-the valve is similar to the air valve on a bicycle tire. Using a small screwdriver, depress the small stem inside the valve. Cover the valve with a shop rag to catch the squirt of fuel.

Set the transmission to neutral and lift the rear, right-hand side of the vehicle (passenger side) using a floor jack and support the car safely on a jack stand.

Locate the fuel filter under the frame rail, near the fuel tank and clean the lines and fittings on both ends of the fuel filter. This will prevent fuel system contamination.

Remove the nuts from the support bracket holding the fuel filter using a wrench or ratchet and socket. Pull the bracket off the filter.

Disconnect the outlet fuel line--the one going towards the engine--using a spring lock coupling tool, which you can buy at most auto parts stores. Then disconnect the quick release coupling from the other end of the filter by pressing the locking tabs; push the fitting against the filter and then pull the line off the filter.

Connect the outlet and inlet fuel lines to the new filter. Make sure the arrow on the side of the filter case is pointing towards the engine. Install the filter on its bracket and secure the bracket to the frame rail.

Lower the vehicle and connect the negative battery cable; tighten the filler cap, start the engine and check for fuel leaks.

Jul 22, 2012 | 2001 Ford Expedition

1 Answer

Overreving with no power and excessive gas consumption air filter cleaned map sensor replaced fuel pump and filter


usually caused by busted diaphram in fuel pressure regulator allowing fuel to be drawn thru regulator directly to intake manifold. Pull vacuum line off regulator, plug line with golf tee, start car and watch to see if gas comes out of regulator. If yes, turn off car, replace regulator. The regulator sits near the fuel rail on the top of the engine as shown below. I will paste replacement instructions below from autozone.com in case you need to replace the regulator. Please let me know if you have any questions.
jturcotte_421.gif


Removal & Installation

4.2L Engine

  1. Relieve the fuel system pressure.
  2. Remove the air cleaner outlet resonator.
  3. Disconnect the engine wiring harness from the retaining clips at the front of the engine.
  4. Disconnect the fuel pressure regulator vacuum line.
  5. Clean any dirt from the fuel pressure regulator and the surrounding area.
  6. Disconnect the fuel return pipe.
  7. Remove the fuel return pipe retainer.
  8. Remove the fuel pressure regulator retainer.
  9. Remove the fuel pressure regulator.
  10. Inspect the regulator filter screen for contamination. If contaminated, replace the fuel pressure regulator.

To install:
  1. Install the regulator filter.
  2. Install the new O-ring on the fuel pressure regulator.
  3. Lubricate the fuel pressure regulator O-ring with clean engine oil.
  4. Push the fuel pressure regulator into the regulator housing on the fuel rail.
  5. Install the fuel pressure regulator retainer. Tighten the regulator retainer screw to 71 inch lbs. (8 Nm).
  6. Install the fuel return pipe retainer. Tighten the return pipe retainer screw to 71 inch lbs. (8 Nm).
  7. Connect the fuel return pipe.
  8. Connect the fuel pressure regulator vacuum line.
  9. Connect the negative battery cable.
  10. Inspect for leaks:
    1. Turn ON the ignition for 2 seconds.
    2. Turn OFF the ignition for 10 seconds.
    3. Turn ON the ignition.
    4. Inspect for fuel leaks.

  11. Install the engine wiring harness into the retaining clips at the front of the engine.
  12. Install the air intake resonator.

Dec 08, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

How to change the fuel filter


Fuel Filter The filter should be inspected for external damage and/or leakage at least once a year. The fuel filter should be changed only as necessary. Toyota Motor Corporation recommends replacing the carbureted fuel filters at 15,000 miles and 30,000 miles on fuel injected models. NOTE: Fuel lines and connections, fuel tank vapor vent system hoses and fuel tank bands should be inspected every 60,000 miles or every 36 months. The fuel tank cap gasket should be replaced 60,000 miles or every 72 months.
---
REMOVAL & INSTALLATION Carbureted Engines The fuel filter on carbureted engines is a plastic cylinder with two ports for the fuel. It is usually located in the engine compartment near the charcoal canister.
  1. Using a pair of pliers, expand the hose clamp on one side of the filter, and slide the clamp further down the hose, past the point to which the filter pipe extends. Remove the other clamp in the same manner. Grasp the clamps and slide them up the hose slightly above the filter ends 88271p10.jpg

  2. Grasp the hoses near the ends and twist them gently to pull them free from the filter pipe. Slide the hose off the end of the fuel filter end 88271p11.jpg

  3. Pull the filter from the clip and discard. Be carefull when removing the filter, some fuel may spill out if not held upright 88271p12.jpg
    To install:
  4. Install the new filter into the clip. The arrow must point towards the hose that runs to the carburetor.
  5. Push the hoses onto the filter pipes, then slide the clamps back into position.
  6. Start the engine and check for leaks.
Fuel Injected Engines 1993-97 MODELS
  1. Turn the ignition switch to the LOCK position. Disconnect the negative battery cable and wait at least 90 seconds before proceeding with working on the fuel system. This will depressureize the fuel system. The fuel filter can be hard to locate on these engines 88271pa1.jpg
    Fig. 4: Exploded view of the fuel filter mounting - 1993-97 models 88271g02.gif
    Fig. 5: Disconnect the negative battery cable prior to all fuel system repairs 88271g03.gif
    CAUTION
    Failure to depressurise the fuel system could cause personal injury.
  2. Disconnect the Intake Air Temperature (IAT) sensor wiring.
  3. Loosen the air cleaner hose clamp bolt, the disconnect the four air cleaner cap clips. Fig. 6: Loosen the air cleaner hose clamp bolt 88271g04.gif

  4. Spearate the air cleaner hose from the throttle body, and remove the air cleaner cap together with the air cleaner hose.
  5. Disconnect the EVAP canister hose from the charcoal canister. Fig. 7: Remove both EVAP hoses from the charcoal canister 88271g05.gif

  6. Remove the charcoal canister from the bracket.
  7. Place a suitable container or shop towel under the fuel filter. Remove the union bolt and two gaskets, then slowly disconnect the fuel inlet hose from the fuel filter outlet. Fig. 8: Remove the union bolt and two gaskets from the fuel filter, then disconnect the inlet hose from the filter 88271g06.gif

  8. Using a special wrench 09631-22020 or equivalent, disconnect the inlet pipe from the fuel filter. Remove the two bolts and the filter from the vehicle. Fig. 9: Using a special tool, disconnect the inlet pipe from the fuel filter 88271g07.gif
    Fig. 10: Remove the two filter mounting bolts, then separate the filter from the vehicle 88271g08.gif
    To install:
  9. Install the fuel filter with the two bolts and tighten them to 43 inch lbs. (5 Nm).
  10. Using the special wrench 09631-22020 or equivalent, connect the inlet pipe to the fuel filter. Tighten to 22 ft. lbs. (30 Nm). Using a torque wrench, tighten with a fulcrum length of 11.81 inch (30cm). Install the fuel inlet hose to the filter outlet using new gaskets and union bolt. Tighten to 22 ft. lbs. 30 Nm). Fig. 11: Install the filter inlet hose to the filter outlet, then tighten to 22 ft. lbs. (29 Nm) 88271g09.gif

  11. Install the charcoal canister to the bracket. Connect the two EVAP hoses to the canister.
  12. Connect the air cleaner hose to the throttle body. Install the air cleaner cap together with the air cleaner hose.
  13. Attach the IAT sensor wiring.
  14. Connect the negative battery cable. Start the engine and check for leaks. Reset any various digital equipment such as radio memory and the clock if necessary.
prev.gif next.gif

Nov 08, 2010 | 1993 Toyota Corolla

1 Answer

Cant find where the fuel fillter is located in our pontiac Grand am 2004


Fuel Filter (behind gas tank) Removal & Installation To Remove:
NOTE: There is no maintenance schedule for fuel filter replacement. Replace the fuel filter if restricted. Inspect the fuel tank internally if you find a restricted fuel filter.
Typical inline fuel filter gm-05-38-686.gif

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Raise and safely support the vehicle.
  4. Remove or disconnect the following:
    • Quick connect fitting at the fuel filter inlet
    • Fuel filter outlet fitting from the fuel filter while holding the filter fitting with a back-up wrench
    • Fuel filter from the vehicle
    • Fuel line O-ring.
To Install:
  1. Position the new fuel filter in the bracket.
  2. Install a new plastic retainer on the fuel inlet line.
  3. Lubricate the new fuel pipe O-ring with clean engine oil.
  4. Install the fuel pipe O-ring.
  5. Reconnect the fuel outlet line to the filter by holding the filter with a back-up wrench and tightening the line fitting to 20 ft lbs (27 Nm).
  6. Lower the vehicle.
  7. Pressurize the fuel system and check for leaks.
prev.gif next.gif

Jun 30, 2010 | Cars & Trucks

1 Answer

Where is fuel pressure regulatore located


For 2000 Chevrolet Truck Blazer 4WD 4.3L SFI 6cyl
If your engine is a 4.3L V-6 with CPI (central point injection) it is inside the upper intake manifold. The upper intake manifold is bolted on top of the normal intake manifold.

The throttle body is mounted on it and your fuel lines terminate into the center of this.


Removal & Installation
  1. Relieve the fuel system pressure.
  2. Remove the air cleaner outlet resonator.
  3. Disconnect the engine wiring harness from the retaining clips at the front of the engine.
  4. Disconnect the fuel pressure regulator vacuum line.
  5. Clean any dirt from the fuel pressure regulator and the surrounding area.
  6. Disconnect the fuel return pipe.
  7. Remove the fuel return pipe retainer.
  8. Remove the fuel pressure regulator retainer.
  9. Remove the fuel pressure regulator.
  10. Inspect the regulator filter screen for contamination. If contaminated, replace the fuel pressure regulator.
To install:


aaf5240.jpg
Fig. Fuel pressure regulator-4.2L engine
  1. Install the regulator filter.
  2. Install the new O-ring on the fuel pressure regulator.
  3. Lubricate the fuel pressure regulator O-ring with clean engine oil.
  4. Push the fuel pressure regulator into the regulator housing on the fuel rail.
  5. Install the fuel pressure regulator retainer. Tighten the regulator retainer screw to 71 inch lbs. (8 Nm).
  6. Install the fuel return pipe retainer. Tighten the return pipe retainer screw to 71 inch lbs. (8 Nm).
  7. Connect the fuel return pipe.
  8. Connect the fuel pressure regulator vacuum line.
  9. Connect the negative battery cable.
  10. Inspect for leaks:
    1. Turn ON the ignition for 2 seconds.
    2. Turn OFF the ignition for 10 seconds.
    3. Turn ON the ignition.
    4. Inspect for fuel leaks.
  11. Install the engine wiring harness into the retaining clips at the front of the engine.
  12. Install the air intake resonator.
Hope help with this (remember rated this post).

Feb 26, 2010 | 2000 Chevrolet Blazer

2 Answers

Where is the fuel filter


On buick LeSabre the fuel filter will be under the car passenger side just in front of the rear tire . Follow the fuel line and you will find it there.

Oct 05, 2009 | 2000 Buick LeSabre

2 Answers

Where is the fuel filter located?


  1. Relieve fuel system pressure.
  2. Safely raise and support the vehicle.
  3. Remove or disconnect the following:
  4. Quick connect fitting at the fuel filter inlet
  • Threaded fitting at the fuel filter outlet
  • Fuel filter from the bracket by sliding to the rear
  • Fuel pipe O-ring seal and discard if damaged
  1. Drain any remaining fuel and discard fuel filter into an approved container.
To Install:
  1. Lubricate the fuel pipe O-ring seal with clean engine oil.
  2. Install or connect the following:
    • Fuel pipe O-ring seal to the fuel pipe
    • Fuel filter forward into the fuel filter bracket
    • Threaded fitting to the fuel filter outlet
      1. Torque to 22 ft. lbs. (30 Nm)
    • Quick connect fitting at the fuel filter inlet
  3. Lower the vehicle
04300ae.gif
It is on your frame rail towards the back of your car.

Aug 30, 2009 | 2003 Cadillac CTS

1 Answer

Who do I locate the fuel filter for my buick lesabre 99?


Fuel Filter Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Relieve the fuel system pressure.
  4. Raise and support the vehicle.
  5. Disconnect the plastic quick connect from the fuel filter inlet.
  6. Unthread the fuel filter from the outlet pipe.
  7. Drain remaining fuel into a gasoline container
86a9bf2.jpg
To Install:
  1. Remove the new fuel filter protective caps.
  2. In the same position as on the old fuel filter, install the new plastic connector retainer on the fuel filter inlet.
  3. With clean engine oil lubricate the new fuel pipe O-ring and install it on the outlet pipe.
  4. Connect the fuel filter inlet to the quick connect fitting.
  5. Thread the fuel filter into the fuel outlet line, and using a back-up wrench prevent the nut from turning torque to 22 ft-lb (30 Nm).
  6. Lower the vehicle.
  7. Install or tighten the fuel cap.
  8. Connect the negative battery cable.
  9. Check for leaks using the following procedure:
    1. Turn ON the ignition for 2 seconds.
    2. Then OFF the ignition for 10 seconds.
    3. Turn ON the ignition.
    4. Inspect for fuel leaks.
  10. Install the fuel injection sight shield.

Apr 02, 2009 | 1999 Buick LeSabre

1 Answer

2003 ford focus fuel filter replacement


  1. Depressurize the fuel system. For additional information, refer to Section 310-00 .
  2. Disconnect the battery ground cable.
  3. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  4. Disconnect the evaporative emission pipe.
  5. Remove the fuel filter outlet pipe. For additional information, refer to Section 310-00 .
  6. Disconnect the fuel filter inlet pipe. For additional information, refer to Section 310-00 .
  7. Remove the fuel filter and bracket.
  8. Remove the fuel filter.
    1. Remove the bolt.
    1. Slide out the fuel filter.
you may need a special tool to release the qucik connects for the fuel lines from the filter.

Dec 31, 2008 | 2003 Ford Focus

1 Answer

Fuel filter


It is located under the hood below or beside the brake booster.

and if you want to replace the fuel filter these is the method

Releave the fuel system pressure Disconnect the negative battery cable If necessary for access remove the air cleaner assembly remove the vlips and detach the hoses from the fuel filter then remove the filter bracket nuts and lift the assembly out of the enginge compartment note the direction the inlet and outlet pipes are facing.Make sure the new filter is installed so that its facing the proper direction.Install the inlet and outlet hoses and secure them with clamps FUEL PRESSURE RELIEF Remove the back seat cushion remove the fuel pump access cover disconnect the fuel pump electrical connector start the engine and wait for it to stall after it stalls turn the ignition switch to the off position.Any residuel fuel pressure in the fuel system in now relieved now

Sep 27, 2008 | 1998 Hyundai Elantra

Not finding what you are looking for?
2001 Volvo V70 Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Mark Jones

Level 2 Expert

76 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...