Question about 1998 Chrysler Concorde

1 Answer

My hood release is broken and I cannot open my hood. Are there any ways to open the hood.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 512 Answers

It is possible to open it but you will need it in the air. you will be able to see where the cable attaches and with a long screwdriver push against it and release the latch

Posted on Dec 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I open hood when cable or latch is broken


If the plastic hood release handle inside is broken, can you reach the steel cable, if so, use a pair of vice grips to grab the cable and pull. Sometimes it helps to have a helper standing at the end of the hood and pop the hood with palm of hand, in the area of under hood release mechanism, at the same time your pulling the cable.

If cable is broken, some makes and models, you can remove front grille and get at under hood release mechanism.

There is usually a primary hood release, inside vehicle, and a secondary release under the hood, you have to slide your hand under the hood to release, sometimes you have to press down on the hood a little to move release. Trying to shut the hood with secondary release engaged can be difficult, you don't have the distance and the weight of hood to swing down.

Nov 04, 2015 | 2007 Chevrolet Chevrolet HHR LT

1 Answer

Hood Release is broken, can not open hood even when I pull on cable,how do I open the hood?


Since you do not say model, try this
http://www.bing.com/videos/search?q=open+hood+with+broken+release&qpvt=open+hood+with+broken+release&FORM=VDRE
open hood with broken release Bing Videos

Mar 26, 2015 | Cars & Trucks

1 Answer

How do I open my hood if the release cable is broken?


Try and get a hold of the cable at any location , You will have to have a pair of pliars , and it usually take a good pull. Short of that is the only way is going straight to the latch, after removing the grill.

Jul 03, 2014 | 2001 Jeep Cherokee

1 Answer

1998 honda crv bonnet wont release to open it what


Try pushing down on the hood while someone else pulls the lever to open the hood. Then lift up and release latch as usual.
Could be broken spring in latch.

Feb 02, 2010 | 2004 Honda CR-V

1 Answer

MY INSIDE HOOD RELEASE HAS BROKEN. IS THERE ANY


depending on where the cable is broken your can still release and open the hood. if it is broken inside the van in the footwell is the easiest...locate the end of the cable and with a set of visegrips pull the cable to release the hood.

Dec 07, 2009 | 1994 Plymouth Grand Voyager

2 Answers

Broken hood release cable. How can I open the hood manually?


The cable is held in place by a metal bracket. If it cam off the bracket it won't work.

Look behind the part you pull and you will see the wire and the outer part of the cable. The end of the outer part of the cable has a groove neer the end. This groove slides onto a slot that is located just behind the pull latch. Once you see it it will make since on how it should go.

You can also grab the outer part of the cable and pull the inner wire. If you can pull the wire almost out, then it is broken. But the chances of that are very low.

Nov 15, 2009 | 2006 Kia Spectra

1 Answer

Does any one know how to open the hood on a 1987 300e if the latch doesn't release


There is a release cable that is attatched to the red releas handle on the drivers under dash panel. You can grab that cable with needle nose pliers to release the hood to the first detent if the handle or cable is broken. There is a secondary release mechanism(called a hood tongue) which routes through the grille where the rectangular slot is once the hood is popped up with the release handle.you can grab the rest of the broken hood tongue with needle nose pliers and pull it out to completly release the hood from the saftey catch. If it is completely broken you can take a long screw driver and push the saftey catch( i beleive to the right) and the hood should be able to open all the way up. Both the hood tongue and the cable(securing portion at release handle) are common failures and break over the years.if it is at the release handle you are having a problem-get a #2 phillips screw driver and remove the release handle to gain access to the loose cable. I hope I have been helpful

Oct 07, 2009 | 1990 Mercedes-Benz 300 Diesel

1 Answer

Broken Hood Release


Hello There

In short no there isn't, however it's most likely your plastic release lever is broken and not the metal cable, you need to open the cover over the release lever, there will be a cable you can pull using a gripper and it will release the bonnet, you can easily replace the plastic llever and it's reletively cheap.

Hope this helps, please don't forget to rate me.

May 20, 2009 | 2003 Toyota Sienna

2 Answers

Hood won't open. Cable is broken and can't get hood to pop.


NO there is no manual way . get a good flash light and look at teh latch through the grill or from under the truck and try and pop it with a long flat blade screw driver

Jan 11, 2009 | 1988 Jeep Cherokee

Not finding what you are looking for?
1998 Chrysler Concorde Logo

356 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...