Question about 1999 Dodge Intrepid

1 Answer

I cant get it back together

I took off the top of my engine and when i did so there was a pipe that ran into both sides of the motor now i cant seen to get it back into place did i do something wrong

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Dodge Master
  • 22,382 Answers

Sounds like you should have fitted it at earlier stage before you the rest on

Posted on Dec 25, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

Hi!2012 Chrysler Town and Country front wheel drive. Where is the starter. Front, back, side? Is it hard to get to?

Front right as you look down on the engine. Follow the dip stick pipe down to it's bottom, (yellow). It will be to the right of where the pipe enters the engine block, fitted from left to right, (red). See photo.


May 01, 2018 | Chrysler Cars & Trucks

1 Answer

Just had the entire coolant system replaced on my 07 Malibu about 5 days later my engine ran great before.they said they took out a sparkplug and it was bent.could they of done something wrong

It is doubtful that they did something wrong. After all, the car ran for 5 days. You would have seen a puddle of coolant under the car or you would have seen the engine overheat if they had not put everything back together correctly.

Apr 24, 2015 | 2007 Chevrolet Malibu

1 Answer

Ran low on oil car shut down added oil to right level car will not start. Took battery cable loose to rebot still willnot start

Seized !!! Engines are not computers, they will not "reboot"! You have heated two metals so hot that they have fused together inside the engine. Sorry you will need a new motor.

Oct 28, 2013 | 2005 Hyundai Elantra

1 Answer

Stalls when trying to accelerate

I had this same problem with my 94 Passport... my mechanic replaced a catylytic converter and it ran like a dream!

Feb 10, 2013 | 1994 Honda Passport

1 Answer

Installing all new drum brakes ford f100 took picture and installed driver side eveything went ok pasenger side a nite mare the spring hooks face the same way for both sides cant figure out how to hook...

Did you by chance mix up the shoes,adjuster etc? Short shoe (primary) will be closest to front of vehicle.(right side of backing plate.) Larger shoe to rear. Seen them put on backwards many times when changing from one side to the other. If you only took picture of drivers side, and your using that for reference, adjuster, shoes etc, will be wrong when you go to opposite side of truck. What year is this truck?

May 25, 2010 | Ford F-100 Cars & Trucks

1 Answer

I just replaced my timing chain on my 302 but when I put it all back together it wont turn over like the motor is locked up and you cant turn the crank by hand??? Did I miss something

Sounds like engine is out of time and pistons are hitting valves locking engine up especially if it turned over and ran before you took it apart this is most likely cause. Remove timeing cover and verify timing marks are properly lined up on gears, then roll engine by hand, if it does not turn then it is hydro locked(fluid in cylinders with valves closed) or mechically locked(dropped a foriegn object into cylinders or bearings/pistons seized). good luck, if out of time you could have bent valves. Need to remove heads and verify if engine has a miss when you get it running.

Mar 01, 2010 | 1989 Ford Mustang

2 Answers

Hello I just replace my motor mounts had to pull muffler from motor put back and it sounds loud so i took it off went to auto zone and the clerk said i needed the donut so after i drilled out the busted...

sounds like the manifold gasket is bad, or the exhaust pipe coming from the manifold head was not properly seated. Got back to auto zone and get a repair/maintence manual for your car , and it should help you get the manifold head gasket/muffler assembly back together.

Jul 12, 2009 | Cadillac Eldorado Cars & Trucks

4 Answers


disconnect carter-gases pipe(over the ref-pos sensor), and if smoke stops, You don't need new engine :)

Jun 09, 2009 | 1995 Suzuki Sidekick

1 Answer

Power steering fluid everywhere

hello it sounds like the high pressure line probaly has a pin hole or possible lek at the factory crimp first thing i would do is have somone start the car turn the wheel all the way to one side the pressure will build up while looking with a flash light look then you may have to put on ramps if it cant be seen from top goodluck

Sep 18, 2008 | 1997 GMC Jimmy

Not finding what you are looking for?
1999 Dodge Intrepid Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

82322 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides