Question about Ford Ranger

1 Answer

Engine jumps while stopped. RPMs will drop or rise slightly when stopped. Problem does not persist when accelerating though.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Hey there, as far as yuor truck is concerned, you may need to check your throttle position sensor, if your truck is equipped with one, it may be bad and that would make your RPM jump and decrease dramatically....

Posted on Dec 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vibration when trans shifts to 4th


it might be transmission problem,check the oil level or add some trans oil treatment.do a scan test & read the number.

Jan 27, 2014 | 2010 Scion xB

1 Answer

Car stalls when stopping / idle


tune up w/ fuel system cleaner/ flush all your fluids/check trans fliud level if smells burnt change it an filter also

Aug 09, 2013 | Jeep Cherokee Cars & Trucks

1 Answer

Why did my speedometer stop working and within minutes my 02 Cadillac Sts stalled and would barely accelerate?


The speedometer and odometer gets a signal from the speed sensor in the side of the transmission where the speedo cable once was.
The problem could be the speed sensor, or something in the wiring, or in the instrument cluster. Or it could be that the transmission is failing internally.

Feb 27, 2013 | 2002 Cadillac Sts

1 Answer

I have a 2000 Nissan Sentra GXE. The engine has a judder on acceleration. Most noticeable between 2 and 3k rpms. It does it on hard throttle at speed also.I have no check engine light on and have replaced...


Try replacing the IAC ( idle air control). They can cause the hesitations and can also cause the vehicles ilde to jump up and down. Also check for any loose vaccuum lines.

Oct 25, 2012 | Cars & Trucks

1 Answer

I have a 1984 rochseter quadrajet. how do you adjust the A.P.T. adjust ment screw


It's called the tip in procedure. You need to run the engine at 2000-2200 rpms and gently cover the choke opening with your hand. If the rpms go up about 100, it is set right. Too much of a rise in rpms, or rpm surging means it is too lean. No rise in rpms means it is too rich. If you pull a vacuum line and the rpms increase, it is too rich; pulling the vacuum line should keep the rpms steady or cause a slight drop. You need to remove the air horn to access the APT screw. You knock out the aluminum plug and install the air horn again to adjust while running the engine. You can 3/8 tap and plug the hole for easy access or drive the aluminum plug back in when done. Turn the APT screw Clockwise to lean it out and counterclockwise to richen it up. To turn it, make a tool with a 5/16 x3 bolt. Cut a notch in the bottom with a hacksaw or grinder about 1/8" wide. The bolt will fit into the hole with the air horn.

Jul 09, 2011 | 1984 GMC C2500

4 Answers

Lack of power


Start with IAC motor, TPS sensor, possible clogged catalytic converter.

May 29, 2009 | 1999 Mitsubishi Galant

1 Answer

Engine jumps/RPMs rise or lower when stopped (with brake).


check the vacuum hose first and if it's been over 30,000 miles and you havn't had a transmission service it is a good idea to have that done

Dec 25, 2008 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...