Question about 1999 GMC Jimmy

1 Answer

My ignition is tuck on

I have a 91 c2500 the switch is stuck on I can start the truck un able to turn it off the switch will not turn. does the switch need replacing or could it be another problem

Posted by on

  • plsnelson43 Dec 25, 2008

    I have the puller what other tools are needed?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 39 Answers

If you can shut the engine off the shift linkage may not be aligned and that makes it not able to fully turn back if it is stuck completely on the switch is probably messed up and would need to be replaced either way you will need to take the column apart and it is easily done with a few tools that are not very expensive. if you need the name of the tools let me know and I can help you through the tear down and repair.

Posted on Dec 25, 2008

  • RoyinGa Dec 25, 2008

    there is a tool that is shaped like a u and has a threaded rod with handle and a wing nut to push a slotted plate that has a lock ring on the steering shaft it is hard to do without it but it can be done

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

91 ford tempo won't start by turning switch but


SORRY BUT THE IGNITION MODULE HAS NOTHING TO DO WITH THIS PROBLEM.REPLACE THE SOLENOID SWITCH AND I BELIEVE YOU PROBLEM WILL BE SOLVED.

Jan 30, 2013 | Cars & Trucks

1 Answer

Car turns over but wont start,checked altinator battery ignition switch distributor fuel filter dnt know what to do


First check for spark at any of the sparkplugs,if you have spark next check fuel pump fuse and relay then check fuel pressure.Turn ignition switch on and listen for pump it should come on for 2 seconds then shut off.

May 09, 2011 | 1990 Chevrolet C2500

2 Answers

When trying to start tuck doesn't turn over no


Battery, and Battery cables off the starter ,starter relay and ignition switch. These are the remaining items in the starting system for no crank and no start.
Get Shop manual and do the appropriate testing for each.

Apr 17, 2010 | 2007 Dodge Ram Truck

1 Answer

Bright lights are stuck on, I went to turn them on one night and then they wouldn't turn off, any ideas on how to fix this or what is causing it?


The dimmer switch is more than likely bad. Its located on the lower steering column next the the ignition switch

Jan 14, 2010 | 1992 Chevrolet C2500

1 Answer

91 Ford Ranger XLT, 4 cyl, manual 5 spd. Engine


most likely right on top of steering colum around have way down

Oct 07, 2009 | 1992 Ford Taurus

1 Answer

How do you un stick a stuck ignition switch on a 1994 Jeep Grand Cherokee?


you can temporarliy "un-stick" the ignition by inserting the key as you would you start the vehicle. then tap the end of the key a few times with the palm of your hand almost as you are trying to drive it in further. this generaly works. but keep in mind that the only fix is to replace the ignition lock cylinder. and make sure that the key is not twisted or bent because that could also inhibit the key from turning properly

Jan 09, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

95 chev truck blows fuses


Your truck has a trailer hitch? Right! Check out the wiring! Frankster016

Oct 19, 2008 | 1995 Chevrolet C2500

Not finding what you are looking for?
1999 GMC Jimmy Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...