Question about 2002 Mazda Protege

Open Question

Block heater How do i install a block heater on a protege 5 (2002) 2.0 liter engine?

Posted by on

5 Suggested Answers

SOURCE: knock sensor location

I'm trying to find this as well...
I've been told its on the back of the engine above the oil filter, however, I cannot locate it...
I have the replacement sensor from Autozone in my hand ($104.XX) yet cannot find where it is supposed to go.  There is a random bolt above a freeze plug, I'm wondering if it is supposed to be in that location.  Not sure that this is even the original motor... eek!

Posted on Aug 06, 2008

txkjun
  • 409 Answers

SOURCE: install block heater on 1996 Nissan maxima 3 liter

It is no a job for a do it yourselfer. I recommend taking it to a qualified repair shop. The heater core is mounted under the dash in the evaperator/heater case and it is a very involved job to disassemble and reassemble the correct way. Sorry.

Posted on Dec 24, 2008

  • 1 Answer

SOURCE: 2002 F-350 7.3 liter deisel engine heater

There should be a small wire harness on the inside of the driver side tow hook under the bumper. The chord is very short and has a cap over the plug. Just reach in and you'll find a black cable about 1/2" thick. There's another wire tapped into it that has the plug end.

Posted on Jan 09, 2009

  • 334 Answers

SOURCE: Need confirmation that 5 Speed Transmission out 1993 Mazda Protege SOHC 1.8 liter Will Bolt up to the Same L-4 Block Engine /Mounts in the 1990 Mazda Protege LX 1.8 liter DOHC

try calling a junkyard and see if they will tell you the enterchange ok good luck

Posted on Apr 18, 2009

  • 131 Answers

SOURCE: How to replace knock senor switch on 2002 mazda protege 5


Removal & Installation

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa95.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Knock sensor removal and installation-Mazda 3

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold bracket.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block using special tool 49H018001 or equivalent.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa96.jpg enlarge_icon.gifenlarge_tooltip.gif GL G

Posted on May 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the diagram for heater core hose on 97 protege


you replace the hoses not block them off .

Mar 03, 2015 | 1997 Mazda Protege

1 Answer

Coolant leak 1994 voyager 3.3


Could be a freeze plug on the engine block. If you have a block heater installed in one of the freeze plug holes, check it for getting too loose and leaking. Pretty common problem with a block heater that's been in there a long time.

Aug 25, 2012 | 1994 Plymouth Voyager

1 Answer

HOW DO A CRANK SENSOR LOOK ON A MAZDA PROTEGE?


check this out on autozone.com web site at plus it depends on the liter of engine but you ca add your liter engine but here is one on there web site at : http://www.autozone.com/autozone/parts/1995-Mazda-Protege/Crankshaft-Position-Sensor/_/N-j1kmtZ8znbj?filterByKeyWord=crank+sensor&fromString=search

Jun 02, 2011 | 1995 Mazda Protege

1 Answer

How can i tell if my 2001 protege has a 1.8 liter engine or a 2.0 liter engine?


It's either a 1.6L or 2.0L. You can contact your local dealer and give them the VIN# and they can tell you for sure. Also, check the sticker in the engine compartment, it will show tune-up specs, year of car, and motor size.

Mar 16, 2010 | 2001 Mazda Protege

2 Answers

Need to know what size (in liters) my engine is(1997mazdaprotege


If you go to onlineconversion.com and enter 90.9 cubic inches to convert to liters, it comes up with 1.489 liters, which is the exact measurement of the 1.5L engine. The DX and LX models are 1.5L, and the ES model comes with a 1.8L.

Feb 03, 2010 | 1997 Mazda Protege

1 Answer

Is the 1993 ford probe v-6 mazda engine the same as 1993 protege


no the ford is a 2.5l but the protege for 1993 is a 1.8 liter

Oct 20, 2009 | 1993 Mazda Protege

1 Answer

How to replace knock senor switch on 2002 mazda protege 5



Removal & Installation

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa95.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Knock sensor removal and installation-Mazda 3

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold bracket.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block using special tool 49H018001 or equivalent.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa96.jpg enlarge_icon.gifenlarge_tooltip.gif GL G

May 09, 2009 | 2002 Mazda Protege

1 Answer

97 Mazda Protege won't start in winter


Theresa,

Plug in your car and listen for a "sizzle" sound. If you hear this then your block heater works.... if not..... Call Canadian Tire!

Jan 05, 2009 | 2002 Mazda Protege

Not finding what you are looking for?
2002 Mazda Protege Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...