Question about 2004 Pontiac Grand Prix

1 Answer

04 pontiac grand prix remote

I have an 04 pontiac grand prix that needs the keyless remotes programmed. i found the instructions that had u remove the mall pgm fuse, etc.

i can't find a mall pgm fuse on this car and wondered if anyone knew how i could program the remote for it.

any help would be great,

thank you

Posted by on

  • Hippy_dd Jan 06, 2009

    does anyone have the instructions, i saw an alternate set of them on here somewhere, for a different process

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Pontiac Master
  • 6,233 Answers

I think you should go for manual first after that it will be easy for u to solve your problem. I had visited this site past 2 months before for my vehicle and find it quite helpful may be you will also get something useful here
Best Manuals

Posted on Nov 17, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: LOOKING FOR A FUSE BOX DIAGRAM FOR 2004 PONTIAC GRAND PRIX GT

It's under the hood, on the driver's side, under a square, black box with a lightning symbol on it. Loosen the flower-shaped screw that holds the lid of the box down, remove the lid, flip it upside down and when you look at the inside of the lid, you'll see a map of all your car's fuses. There's also a fuse diagram on the very end of the dash, but it's accessible only when you open the driver's side door. When you're driving, that end of the dash is blocked by the closed door.

Posted on Jul 01, 2009

  • 1 Answer

SOURCE: where is the MALL PGM plug 2006 pontiac g6

Where is the MALL PGM fues on a 2001 Gram Am.

Posted on Dec 24, 2009

  • 92 Answers

SOURCE: 2004 PONTIAC GRAND PRIX FUSE BOX DIAGRAM

The diagram is on the fuse box cover or lid (depending on which fusebox, cabin or engine compartment. The diagram is also in the owner's manual.

Posted on Feb 08, 2010

  • 14 Answers

SOURCE: where is the keyless entry receiver located at in

Between the two rear speakers. You are going to need to remove the back seat to get under the pannel.

Posted on Jun 25, 2010

  • 109 Answers

SOURCE: 1995 Grand Prix: my pontiac grand prix abs light is on 1995 grand ...

sensor might be dirty, try removing them and cleaning them. Dont use sprays as they pose a threat more than they fix. Check tires to see if there is one that might be WAY lower than the rest. Or consider taking it to a shop if you cant find the rigth abs sensor.

Posted on Jun 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I program keyless entry on my 2002 grand prix? I have tried the way I found by removing mall pgm fuse n open door n turn key to acc. Doesnt work. The fob I have was for gp why it not work?


Important: All transmitters which are to be recognized by the remote control door lock transmitter (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to four transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.
  1. Remove the ignition key from the ignition lock cylinder.
  2. Close all of the doors.
  3. Remove the MALL PGM fuse from the fuse block.
  4. Insert the ignition key into the ignition lock cylinder.
  5. Turn the ignition to ACC.
  6. The body control module (BCM) will perform the following in order to identify the type of BCM installed in the vehicle:
    ?€¢
    Flash the seat belt indicator 1, 2, or 3 times.


    ?€¢
    Chime 1, 2, or 3 times.

  7. Turn the ignition to OFF, and then back to ACC within 1 second.
  8. The BCM may begin to chime and flash diagnostic trouble codes (DTCs). If the BCM has stored any DTCs, refer to Diagnostic System Check - Body Control System in Body Control System.
  9. Open and then close any vehicle door.
  10. The BCM will chime in order to confirm that the programming mode has been entered.
  11. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for approximately 14 seconds.
  12. Important: After approximately 7 seconds the BCM will chime once to confirm that synchronization has been completed. After approximately 14 seconds the BCM will chime a second time to confirm that the programming has been completed.
  13. Repeat the previous step in order to program each additional transmitter.
  14. Remove the ignition key from the ignition lock cylinder.
  15. Install the MALL PGM fuse into the fuse block.
  16. Operate the functions of each transmitter in order to verify correct system operation.

Jun 12, 2015 | 2002 Pontiac Grand Prix

1 Answer

How to program a new alarm remote


Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver's seat.
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation .



Hope this helps, I found it online

-Scott

Feb 19, 2015 | 2004 Pontiac Grand Prix

1 Answer

Programming instructions for 2004 Oldsmobile Alero keyless remote


I have programmed my 2003 Pontiac Grand Prix remotes without going to dealer. Cadilac dealer could not for some reason, but I was able to. I don't know if your Olds is similar.

Nov 30, 2013 | Oldsmobile Alero Cars & Trucks

1 Answer

How to reprogram a key fob


IMPORTANT: Before entering programming mode, have in possession all of the remotes you
will be useing on the vehicle. Once you program the remote. all previous remotes that were
programmed will be erased from memory. The other remotes will not be functional until you
program the them again.
1. Remove the key from the ignition.
2. Close all doors.
3. Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or
owner's manual to properly locate the "MALL PGM" fuse.
4. Insert the key into the ignition, and turn to the ACC position.
5. Turn the key to OFF and then back to ACC within 1 second.
6. Open and close any vehicle door. A chime will be heard when the system enters into
programming mode.
7. Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds.
IMPORTANT: After 7 seconds, a chime may be heard confirming successful
synchronization. It is necessary to wait approximately 14 seconds for a second chime
that will confirm successful programming.
8. Repeat step 7 now for each additional remotes to be programmed including any existing
remotes.
9. Remove key from ignition.
10. Install the "MALL PGM" fuse back into the fuse panel and test remote(s).

Sep 10, 2012 | 1999 Pontiac Grand Prix

1 Answer

Keyless remote instructions for 99 pontiac grand prix do not work


Is the battery good in the remote? Is the remote working? Did the car come with keyless remote?
If you stop by a big box part store they have a tester to check the remote. Sometimes when the battery is replaced there is a solder joint that brakes.

Feb 14, 2011 | 1999 Pontiac Grand Prix

1 Answer

WHERE IS THE MALL PGM FUSE PANEL LOCATED ON A 2000 PONTIAC GRAND PRIX


There is a 10A MALL/CLUSTER FUSE in the fuse block. There is no MALL/PGM fuse panel.

Oct 22, 2010 | 2000 Pontiac Grand Prix

1 Answer

I need to program the key less entry


IMPORTANT: Before entering programming mode, have in possession all of the remotes you
will be useing on the vehicle. Once you program the remote. all previous remotes that were
programmed will be erased from memory. The other remotes will not be functional until you
program the them again.

1. Remove the key from the ignition.
2. Close all doors.
3. Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or
owner's manual to properly locate the "MALL PGM" fuse.

4. Insert the key into the ignition, and turn to the ACC position.
5. Turn the key to OFF and then back to ACC within 1 second.
6. Open and close any vehicle door. A chime will be heard when the system enters into
programming mode.

7. Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds.
IMPORTANT: After 7 seconds, a chime may be heard confirming successful
synchronization. It is necessary to wait approximately 14 seconds for a second chime
that will confirm successful programming.

8. Repeat step 7 now for each additional remotes to be programmed including any existing
remotes.

9. Remove key from ignition.
10. Install the "MALL PGM" fuse back into the fuse panel and test remote(s).

May 10, 2010 | 1998 Pontiac Grand Prix

Not finding what you are looking for?
2004 Pontiac Grand Prix Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

81342 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...