Question about 2001 Chevrolet Venture

1 Answer

I can't find the thermostat on my 2001 chevy venture

Where is the thermostat on a 2001 chevy venture

Posted by on

  • solieswrench May 11, 2010

    Follow the top radiator hose to engine there is where the thermostat should be.

  • Vitally Alcher Jul 13, 2014

    ono tiop hose

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 443 Answers

The top radiator hose

Posted on Jan 25, 2009

6 Suggested Answers

ZJLimited
  • 17970 Answers

SOURCE: how do I remove the thermostat from my 2001 chevy

2001 Chevrolet Truck Venture FWD 3.4L SFI 6cyl

Removal & Installation

  1. Remove the air cleaner and duct assembly.
  2. Drain the coolant until the coolant level is below the thermostat.
  3. Remove the crossover exhaust pipe.
  4. Remove the radiator hose from the thermostat housing.
  5. Remove the thermostat housing bolts and clean any sealer from the bolt threads.
    30d8f30.jpg

    Fig. Remove the housing bolts
  6. Remove the thermostat housing and gasket.
  7. Remove the thermostat.
  8. Clean the mating surfaces.

To install:


6c98478.jpg

Fig. The removal and installation of the thermostat
  1. Install the thermostat.
  2. Install the thermostat housing and gasket.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the thermostat housing bolts and tighten them to 18 ft. lbs. (25 Nm).
  4. Install the radiator hose to the thermostat housing.
  5. Install the crossover exhaust pipe.
  6. Install the air cleaner and duct assembly.
  7. Fill the cooling system.

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the air cleaner intake duct.
  3. Partially drain the cooling system.
  4. Remove the radiator inlet hose from the thermostat housing.
  5. Remove the thermostat housing bolts.
  6. Remove the thermostat.
  7. Clean and inspect the thermostat housing gasket mating surfaces.
To install:
  1. Install the thermostat.
  2. Install the thermostat housing.
  3. Install the thermostat housing bolts and tighten to 18 ft. lbs. (25 Nm).
  4. Install the radiator inlet hose to the thermostat housing.
  5. Install the air cleaner intake duct.
  6. Fill the cooling system.
  7. Start the engine and check for leaks.
3.9L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Release the tension on the hose clamp at the thermostat housing and remove coolant hose.
  4. Remove the thermostat housing mounting bolts and remove the thermostat housing.

    5734720.jpg
    Fig. Remove the thermostat housing to access the thermostat-3.9L engine shown
  5. Remove the thermostat.
To install:
  1. Install the thermostat.
  2. Install the thermostat housing and tighten the bolts to 18 ft. lbs. (25 Nm).
  3. Install the coolant hose to the thermostat housing and install the hose clamp.
  4. Refill the cooling system to the correct level.
  5. Start the engine and check for leaks.

I hope help you whit thie (remember rated this help) Have a nice day and good luck.

Posted on Sep 23, 2009

  • 1 Answer

SOURCE: Thermostat in a 2003 chevy venture van

the bottom boult is hard but can be done need to use a 10 or 12 stubby wrench and take a pry bar and lighty pry heat shild away to get bottom bolt dont need to take it out all the way just loosen and slide down

Posted on Aug 17, 2008

  • 87 Answers

SOURCE: my chevy venture 2001

Is the fluid full ? is the fluid clean compared to new fluid ? if you answered no to both of these questions you may need a transmission

Posted on Dec 19, 2008

  • 1 Answer

SOURCE: Thermostat in a 2003 chevy venture van

no you dont need a special tool you have to take the throttle body off it makes it sooooooo much more simple.

Posted on Jan 27, 2009

bunnydawg
  • 5158 Answers

SOURCE: reset the computer system of 2001 chevy venture

Unhook the battery for about ten minutes or so... if you have an after market stereo that requires a code make sure you know it.

Robert

Please take a momemt to rate this solution thanks

Posted on Jan 29, 2009

  • 29 Answers

SOURCE: Help changing thermostat 2002 chevy venture

You will have a rubber gasket on the 2002 venture and not a gasket. I have had my Venture since 2002 and I do not use sealant since the rubber gasket seals the fluid in the thermostat housing. Most of the other directions noted are right except that you only have to take out the upper themostat housing bolt and leave the other bolt in the intake housing. The thermostat housing has a slot to allow you to remove it straight up if you have removed all items that are in the way.

Posted on Apr 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just bought a 2001 Chevy venture and the automatic door opener button for the sliding doors doesn't work. How can we fix it our selves?


Does the door unlatch but not open? Check out this site for assistance: http://www.justanswer.com/chevy/0nkic-2004-chevy-venture-passenger-side-power-sliding-door.html

Oct 01, 2014 | 2001 Chevrolet Venture

2 Answers

2001 Chevy Venture - My heat is not as hot as usual and blows cool when idle. Coolant level is fine. Temp Gauge isn't working.


Sounds like you need to have the cooling system flushed out then have them put a new themostat in it. If that dont fix the prob you might have to put a new heater core in it or radiator.

Jan 23, 2013 | 2001 Chevrolet Venture

2 Answers

Have changed the water pump, thermostat, radiator, radiator cap, all hoses. 2001 chevy venture, still running hot? How long does it take to bleed the cooling system?


If the system fills via an expansion tank, I would recommend removing the top hose from the radiator and filling the system by pouring the coolant in through the hose until it begins to flow out of the upper radiator port. Reconnect the hose and then fill the expansion tank. That should take care of it.

Jun 26, 2011 | 2001 Chevrolet Venture

2 Answers

Where is thermostat on 2001 chevy venture van with v6 engine


under the intake plenum, which will have to be removed before you can access the thermostat.
I suggest having it done by a garage mechanic.

May 23, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

No Heat


check your coolant level...if its too low then it will not flow through the heater core correctly to generate the heat.

Jan 15, 2009 | 2001 Chevrolet Venture

2 Answers

Thermostat in a 2003 chevy venture van


no you dont need a special tool you have to take the throttle body off it makes it sooooooo much more simple.

Nov 27, 2008 | 2004 Chevrolet Venture Passanger

Not finding what you are looking for?
2001 Chevrolet Venture Logo

Related Topics:

792 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...